Marantz PMD570 manual Copyright

Page 4

 

ANTENNA

 

LEAD IN

 

WIRE

GROUND

ANTENNA

CLAMP

DISCHARGE

 

UNIT

 

(NEC SECTION

 

810-20)

ELECTRIC

GROUNDING

SERVICE

CONDUCTORS

EQUIPMENT

(NEC SECTION

 

 

810-21)

GROUND CLAMPS

POWER SERVICE

 

GROUNDING

 

ELECTRODE SYSTEM

 

(NEC ART 250, PART H)

FIGURE 1

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

NEC - NATIONAL ELECTRICAL CODE

NOTE TO CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV (Cable-TV) system installer's attention to Article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter- ference in a residential installation. This equipment generates, uses and can radiate radio frequency en- ergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran- tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is con- nected.

•Consult the dealer or an experienced radio/TV tech- nician for help.

NOTE:Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the equipment.

WARNINGS

Do not expose the equipment to rain or moisture.

Do not remove the cover from the equipment.

Do not insert anything into the equipment through the ventilation holes.

Do not cover the ventilation with any items such as tablecloths, newspapers, curtains, etc.

No naked flame sources, such as lighted candles, should be placed on the equipment.

When setting up the recorder ensure that:

•it will not be exposed to interference from external equipment.

•it will not be exposed to electrostatic dis- charges.

•it will not be exposed to direct sunlight.

•heavy objects are not placed on the recorder.

Copyright

Recording and playback of any material may require consent. For further information refer to the following US ordinances:

•Copyright act of 1956

•Dramatic and Musical Performance Act 1958

•Performers Protection Acts 1963 and 1972

•any subsequent statutory enactments and orders

- 4 -

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model PMD570 User Guide Risk of Electric Shock Important Safety Instructions Copyright CE marking only EU version English Editing and setup Table of ContentsEdit Menu Package contents Setup IntroductionComputer compatible Audio inputs may be fromTracks FeaturesEDL marks 6a. Connect RC600 wired Connect line level XLR equipment for recordingThis connection makes it easy to Copy audio files to or from yourInitialize Recording setupStart-up Power ON/OFF button Turn to adjust headphoneVolume ExampleCF card access light green CF card compartmentCard eject button To eject a CF cardDefault display Is elapsed time on Default display is5a. Display button Alternate information displaysREC label Total labelTrack label Remain labelMark label Lower alphanumeric displayLine label Record iconHow to change Presets Selected Preset7a. Menu CurrentlyExample display With level margin at02dB before Jog WheelHow to select tracks during playback How to select an EDL markHow to adjust record level How to adjust record balanceHow to start a new track How to add an EDL mark while recordingStop/CANCEL button Shift buttonBack At stopTrim L & R Pin 1 groundConnectors Spdif Digital OUT jack RCAAnalog OUT jacks O portRS-232C connector Using serial communication, aRemote Menu setting StartPause Menu mode PresetsTable of Preset defaults PCM/MP2/MP3General Menu procedure Preset defaultsHow to select inputs for recording How to set or change the Date and time How to set or change the Date Form Chart of RecFormat Parameters RecFormatRecFormat parameters Channels AlgorithmHow to set or change the RecFormat parameters Change to Kbps Push and release the Jog Wheel when correctDisplay shows Shows change toWav 44.1 Stereo Bwf Pre Record Auto MarkManual TR Auto TrkMinute track TrackSeamlsPly Seamless Play SilentSkp Silent Skip Auto Cue Play Mode NormalRepeat All Repeat TRKEDL Play EDL Play menu turns EDL Play On or OffOff Display duringID1Dscrpt, ID2Origin, ID3OrRef Broadcast Wave ID numbers Default Menu Default TrkERASE Renumber tracksDisplay returns to so you can erase another track Display returns to so you can erase another mark TrkMkERASEAllMkERASE Format CF card To Format a CF cardHow to connect via the I/O port PortLocating EDL Marks Skip marksLoop marks EDL marks and the beginning of a TrackHow to Edit EDL marks EDL mark types PointSkip LoopA and LoopBPage Command format Start character End character 0DhHost sends a command that causes a change in PMD570 status Hand shake flow charts for control commandsAscii code @0DS01CR Play Table of Status Request Status Information codes Status Request Information CodePCM Troubleshooting Care and MaintenanceSpecifications1 Digital audio systemLimited Warranty How You Can Get ServiceMarantz is a registered trademark 2004/4
Top Page Image Contents