Toshiba RD-XS35SU This HDD/DVD video recorder employs a Laser System, See service procedure

Page 2

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE NE

PAS OUVRIR

WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilat- eral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclo- sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is in- tended to alert the user to the presence of important operat- ing and maintenance (servicing) instructions in the literature accompanying the appliance.

The symbol for CLASS II (Double Insulation)

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

 

TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE

 

ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL

 

ONLY.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

 

INSERT.

ATTENTION:

POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA

 

FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

CAUTION:

This HDD/DVD video recorder employs a Laser System.

 

To ensure proper use of this product, please read this owner’s manual carefully and retain for

 

future reference. Should the unit require maintenance, contact an authorized service location -

 

see service procedure.

 

Use of controls or adjustments or performance of procedures other than those specified herein

 

may result in hazardous radiation exposure.

 

To prevent direct exposure to laser beam, do not try to open the enclosure.

 

Visible and invisible laser radiation when open and interlocks defeated.

 

DO NOT STARE INTO BEAM.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate the equipment.

2

Image 2
Contents RD-XS35SU RD-XS35SC May result in hazardous radiation exposure See service procedureThis HDD/DVD video recorder employs a Laser System Location of the required label Important Safety Instructions Additional Safety Instructions Introduction PrecautionsWhen not in use Power outage ExemptionsIntroduction Precautions WaitConnections Installation procedure Accessories Remote control Batteries AAA xAbout the hard disc drive HDD About this productSome differences Playback RestrictionsChoosing a disc Using different disc types for different purposesFor recording / playback Disc Mark Specification Remarks For playback only Disc Mark Specification Remarks DiscDVD-RAM discs with cartridges are recommended for recording On DVD-RAM discsIntroduction Choosing a disc Marks on DVD video discs On DVD-R discsOn DVD-RW discs On handling discs Structure of disc contentsOn cleaning discs On storing discsTable of Contents Open the cover Insert batteries AAA size Preparation of the remote controlOperating with the remote control Close the coverWhen you connect an audio system Connection procedureWhen you connect a TV equipped with audio/ video inputs Connecting an antenna and TV ConnectionsConnect the power cord of the recorder to a wall outlet Connect to a TV equiped with audio/video inputsConnecting to cable TV signal You will need toThis set-up will allow you to Connecting to a satellite system When the satellite system has audio/video outputsConnecting the G-LINKcable Connecting to a TV equipped with component video inputs Connecting to an audio system Make the setting onPage Basic setup Starting up the recorder Basic setupTurning the power on Startup/finishing closing iconsIf a message appears Press To select Change system Settings, then press Enter TV Guide On Screen setupPress To select Setup Press To select No, repeat setup Process, then press EnterPress / to select, then press Enter Setup selectionCountry ZIP or postal code Cable serviceBasic setup TV Guide On Screen setup Cable connectionTuning channel for the cable box Cable inputCable box brand name 12Antenna connection Press / to select, then press Enter 13ConfirmationRead the information and press Enter 14Confirmation15Information Press / to select Initial settings, then press Enter Language settingPress Setup To select Language, then pressSatellite set top box setting Press Setup to display the setup menuPress Adjust or / to set DBS to Not used or Use Basic setup Satellite set top box setting Press EnterSatellite set top box brand code RCAPress / to select Audio out select, then press Enter Output sound settingPress / to select Picture/Audio settings, then press Enter Once the proper setting is selected, press Press / to select the output sound formatPress / to select TV shape, then press TV shape settingPress / to select Display settings, then press Enter When the proper setting is selected, press Press / to select the picture shapeRelease TV Code Remote control settingsOperating your TV with the remote control Take this step according to your preference and usageBrand code table JVCSetting up the recorder Press Setup Press / to select Operational settings, then press EnterDisabling the remote control for a temporary period Your Responsibility Limited Ninety 90 Day Warranty on LaborLimited One 1 Year Warranty on Parts Rental UnitsHow to Obtain Warranty Services Page Memo Printed on 70% Recycled Paper
Related manuals
Manual 225 pages 61.34 Kb