Toshiba RD-XS35SU, RD-XS35SC owner manual Connecting an antenna and TV, Connections

Page 20

Connections

Connecting an antenna and TV

Connect your TV and the antenna to this recorder for recording and to view broadcast signals on the TV.

1 Disconnect the antenna cable from your TV, and connect it to the RF IN (FROM ANT.) terminal on the recorder.

2 Using the supplied coaxial cable of this recorder, connect the RF OUT (TO TV) terminal to the TV.

To RF IN (FROM ANT.) 1

To RF OUT (TO TV) 2

Coaxial cable (supplied)

e.g.

VHF/UHF antenna

Antenna cable (not supplied)

TV

2 To antenna input

Antenna splitter

(not supplied)

		Types of an antenna terminal
	VHF/UHF	may vary depending on the TV.
	VHF/UHF	Check the type on your TV, and
		Check the type on your TV, and
		connect properly using either
		method as shown.

For connecting to a cable box or a satellite system, see page 22 to 25.

Note

•This connection ensures broadcast signals to be passed through to your TV. Unlike a VCR, you cannot assign channel 3 or 4 to playback from this recorder. The antenna input only passes through the broadcast signals to your TV.

Therefore to playback video from this recorder you must connect it to a video input on your TV. (See the next page.)

20

Image 20

Contents RD-XS35SU RD-XS35SC May result in hazardous radiation exposure See service procedureThis HDD/DVD video recorder employs a Laser System Location of the required label Important Safety Instructions Additional Safety Instructions Introduction PrecautionsWhen not in use Power outage ExemptionsIntroduction Precautions WaitConnections Installation procedure Accessories Remote control Batteries AAA xAbout this product Some differencesAbout the hard disc drive HDD Playback RestrictionsChoosing a disc Using different disc types for different purposesFor recording / playback Disc Mark Specification Remarks For playback only Disc Mark Specification Remarks DiscDVD-RAM discs with cartridges are recommended for recording On DVD-RAM discsIntroduction Choosing a disc Marks on DVD video discs On DVD-R discsOn DVD-RW discs Structure of disc contents On cleaning discsOn handling discs On storing discsTable of Contents Preparation of the remote control Operating with the remote controlOpen the cover Insert batteries AAA size Close the coverWhen you connect an audio system Connection procedureWhen you connect a TV equipped with audio/ video inputs Connecting an antenna and TV ConnectionsConnect the power cord of the recorder to a wall outlet Connect to a TV equiped with audio/video inputsConnecting to cable TV signal You will need toThis set-up will allow you to Connecting to a satellite system When the satellite system has audio/video outputsConnecting the G-LINKcable Connecting to a TV equipped with component video inputs Connecting to an audio system Make the setting onPage Basic setup Basic setup Turning the power onStarting up the recorder Startup/finishing closing iconsIf a message appears TV Guide On Screen setup Press To select SetupPress To select Change system Settings, then press Enter Press To select No, repeat setup Process, then press EnterPress / to select, then press Enter Setup selectionCountry Cable service Basic setup TV Guide On Screen setupZIP or postal code Cable connectionTuning channel for the cable box Cable inputCable box brand name 12Antenna connection Press / to select, then press Enter 13ConfirmationRead the information and press Enter 14Confirmation15Information Language setting Press SetupPress / to select Initial settings, then press Enter To select Language, then pressSatellite set top box setting Press Setup to display the setup menuPress Adjust or / to set DBS to Not used or Use Basic setup Satellite set top box setting Press EnterSatellite set top box brand code RCAPress / to select Audio out select, then press Enter Output sound settingPress / to select Picture/Audio settings, then press Enter Once the proper setting is selected, press Press / to select the output sound formatPress / to select TV shape, then press TV shape settingPress / to select Display settings, then press Enter When the proper setting is selected, press Press / to select the picture shapeRemote control settings Operating your TV with the remote controlRelease TV Code Take this step according to your preference and usageBrand code table JVCSetting up the recorder Press Setup Press / to select Operational settings, then press EnterDisabling the remote control for a temporary period Limited Ninety 90 Day Warranty on Labor Limited One 1 Year Warranty on PartsYour Responsibility Rental UnitsHow to Obtain Warranty Services Page Memo Printed on 70% Recycled Paper

Related manuals

Manual 225 pages 61.34 Kb