Philips MCM196D quick start Radio Reception, Tuning to radio stations, Programming radio stations

Page 18

Radio Reception

English

M I C R O S Y S T E M M C M 1 9 6 D

 

Tuning to radio stations

1Select TUNER source.

2Press SOURCE on the set repeatedly or press TUNER on the remote repeatedly until the desired waveband (FM or MW) is displayed.

3Press down on TUNING 4 ¢ (or 4

¢on the remote control) and release button.

➜The radio automatically tunes to a station with sufficient reception. Display indication during automatic tuning: SEARCH.

4Repeat step 3 if necessary until you find the desired station.

●To tune to a weak station, press TUNING 4 ¢ (or 4 ¢ on the remote control) briefly and repeatedly until you have found optimal reception.

Automatic programming

Automatic programming will start with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden.The system will only programme stations which are not in the memory already.

1Press ALBUM/PRESET 4 3 to select the preset number where programming should start.

Note:

– If no preset number is selected, default is preset

(1) and all your presets will be overridden.

2Press PROGRAM for more than 2 seconds to activate programming.

➜ AUTO is displayed and available stations are programmed in order of waveband reception strength.The first preset automatically stored will then be played.

Manual programming

1Tune to your desired station (see Tuning to radio stations).

2Press PROGRAM to activate programming. ➜ PROG flashes in the display.

3Press ALBUM/PRESET 4 3 to allocate a number from 1 to 20 to this station.

4Press PROGRAM again to confirm the setting. ➜ PROG disappears, the preset number and the frequency of the preset station are shown.

5Repeat the above four steps to store other stations.

Programming radio stations

● You can override a preset station by storing

You can store up to a total of 40 radio stations

 

another frequency in its place.

in the memory.

 

 

 

 

 

 

 

 

Tuning to preset radio stations

 

● Press ALBUM/PRESET 4 3 until the desired

 

 

preset station is displayed.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Docking Entertainment System MCM196DImportante C R O S Y S T E M M C M 1 9 6 D For Customer Use Returning the enclosed cardRegistering your product guar Class II equipment symbol Disconnet device shall remain Readily operableMaterials English FrançaisIndex Contents General Information Supplied accessoriesSafety Information Environmental InformationTo establish a safe volume level Hearing SafetyListen at a moderate volume Set your volume control at a low settingRear connections PowerPreparations Antenna Connection AM AntennaFM Antenna Before using the remote controlReplacing battery lithium CR2025 into the remote control Speakers Connection Front SpeakersControls on the system and remote control Controls available on the remote control onlyBasic Functions First time setup/power upTo reinstall Plug and Play To exit without storing the Plug and PlaySwitching the system on Adjusting volume and soundPower-saving automatic standby Basic playback controls CD/MP3 OperationLoading a disc Playing an MP3/WMA discReviewing the programme Different play modes Shuffle and RepeatProgramming track numbers Erasing the programmeRadio Reception Tuning to radio stationsTuning to preset radio stations Programming radio stationsGeneral information on recording Tape Operation/RecordingTape playback Synchro start CD recordingMaintenance Recording from the radio Listening to an external sourceSetting the timer Clock/TimerSetting the clock Activating and deactivatingPlaying iPod using the dock Dock for iPodCharging iPod battery using the dock Eco power standby mode, iPod cannot be chargedSpecifications TroubleshootingNo Disc is displayed Make sure the MP3-CD was recorded within Check the speaker connections and locationButtons 2, ¡1, 2 and Volume can function only Philips Limited Warranty ONE 1 Year Meet Philips at the Internet
Top Page Image Contents