Heat Controller RAH-123G owner manual How to set, To cancel the timer, press theTimer 0.5-24hr pad

0.5-24HR

TIMER

Owner’s Manual Room Air Heat Pump with R-410A Heat Controller, Inc.

Timer/DelayOFF—WhenOFF—theWhenair condthe airconditioneris on, is on, it can be set to automatically turn off in 0.5

to 24 hours.

How to set:

Press theTimer 0.5 –24hrpad on the unit or

the	TIMER	pad on the remote control. Each
	0.5-24HR DELAY

touch of the Increase � / Decrease � pads on the unit or the Increase + / Decrease – pads on

the remote control will set the timer in

0.5hour or 1hour intervals(the intervals is

0.5hour as the delay timer below 10 hours;

the intervals is 1 hour as the delay timer above 10 hours) The Set light will turn on

while setting.

To review the remaining time on the Timer

0.5 –24hrtimer, press theTimer 0.5–24hrpad on the

unit or the DELAY pad on the remote control.

Use the Increase � / Decrease � pads on the unit or the Increase + / Decrease – pads on the

remote control to set a new time if desired.

To cancel the timer, press theTimer 0.5–24hr pad

until the light on the Timer 0.5–24hrpad goes off.

Remote Control

�To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.

�The remote control signal has a range of up to 20 feet.

�Make sure nothing is between the air conditioner and the remote control that could block the signal.

�Make sure batteries are fresh and installed correctly as indicated on the remote control.

Cool Mode

Use the Cool mode at Low, Med, High or Auto Fan Speed for cooling. Use the Temperature Increase � /Decrease �pads to set the desired temperature between 61°F and 86°F in 1°F increments.

The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on

while set to a Cool setting or if turned from a fan setting to a Cool setting, it may take approximately 3 minutes

for the compressor to start and cooling to begin.

This time delay is required to protect the compressor.

Cooling Descriptions

For Normal Cooling—Select the Cool mode and High or Med fan with a middle set temperature.

For Maximum Cooling—Select the Cool mode and High fan with a lower set temperature.

For Quieter & Nighttime Cooling—Select the Cool mode and Low fan with a middle set

temperature.

Energy Saver Mode

Controls the fan.

ON—The fan will cycle on and off with the compressor. This results in wider variations of room temperature and humidity. Normally used

when the room is unoccupied. NOTE: The fan may continue to run for a short time after the compressor cycles off.

OFF—The fan runs all the time, while the compressor cycles on and off.

Fan Only Mode

Use the Fan Only Mode at Low, Med or High fan speed to provide air circulation and filtering without cooling. Since fan only settings do not provide cooling, a Set temperature cannot be entered. The room temperature will appear in the display.

NOTE: Auto Fan Speed cannot be used when in the Fan Only Mode.

Heat Mode (On some models)

Use the Heat mode at Low, Med, High or Auto Fan Speed for heating. Use the Temperature Increase /Decrease pads to set the desired temperature between 61°F and 86°F in 1°F increments.

Auto Fan Speed

Set to Auto fan speed for the fan speed to auto- matically set to the speed needed to provide opti- mum comfort settings with the set temperature. If the room needs more cooling, the fan speed will automatically increase. If the room needs less cooling, the fan speed will automatically decrease.

NOTE: Auto Fan Speed cannot be used when in the Fan Only Mode.

Power Outage Recovery Feature

In the case of a power outage or interruption, the

unit will automatically re-start in the settings last used after the power is restored. If the Timer/Delay0.5-24hr

feature was set, it will resume countdown. You may need to set a new time if desired.

13