EAW JFX200 specifications Dimensional Drawing, Input Panel, Specifications, Net Weight 26.4, 29.1

SPECIFICATIONS JFX200

DIMENSIONAL DRAWING

A	C	B
	L
	22.5°	45°
		B
A		8.70
	TOP	10.27	1.46	4.46		(7.04)
5.40	13.68	6.62		1.86	1.80
					INPUT
8.15
			19.33
6.50		22.25				C
					2X 6.87	L

			2X				8.50
	10.50		HANDLE
							3.08
(11.09)	GRILLE PARTIALLY SHOWN			4.50	.98		2X 3.44
VIEW A-A	FRONT	6.50	RIGHT SIDE		2.50		VIEW B-B
	CL					BACK
	5.00				NOTES

8.70	1. SYMBOL INDICATES MOUNTING POINT, 3/8-16
15.25	THREADED HOLE (PI ANGLE)
	2. SYMBOL INDICATES MOUNTING POINT, 5/16-18 T-NUT
	FOR OMNI MOUNT SERIES 300.
TOP HAT	3. SYMBOL INDICATES 3.00 X 1.35 FLY TRACK.
	4. SYMBOL INDICATES 11.00 X 1.35 FLY TRACK.
6.75
	5. SYMBOL INDICATES CENTER OF BALANCE
BOTTOM
	6. WEIGHT APPROX. 58 LBS.

7. SHIPPING WEIGHT APPROX. 64 LBS

0002817 (B) 9/4/02

Manufacturing tolerances are +/- 0.13 and +/- 1°

INPUT PANEL

WHITINSVILLE, MA USA

JFX200

S/N

FULL-RANGE

PASSIVE

PIN 1--...--

PIN 1+...+

BI-AMP

PIN 1--...LF--

PIN 1+...LF+

PIN 2--...HF--

PIN 2+...HF+

N E U T R I K

NL 4 MPR

N E U T R I K

A & E SPECIFICATIONS

The 2-way full-range loudspeaker shall incorporate a 12-in LF cone and a 3-in voice coil neodymium HF compression driver. The LF cone shall be mounted in a vented enclosure tuned for optimum low frequency response. The HF driver shall be loaded on an axis-symmetrical, 1.4-in exit Wave Guide Plate™ with a nominal conical beamwidth of 90 degrees. An internal passive crossover network shall offer either passive or bi- amplified operation, configurable via a power mode switch on the input panel.

System frequency response shall vary no more than +3 dB from 90 Hz to 16 kHz measured on axis. When amplified using the internal passive crossover network, the loudspeaker shall produce a sound pressure level of 97 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 130 dB SPL on axis at 1 meter. It shall handle 500 watts of amplifier power and shall have a nominal impedance of 8 ohms. When bi-amplified, the LF sec- tion shall produce a sound pressure level of 97 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capa- ble of producing a peak output of 130 dB SPL on axis at 1 meter. It shall handle 500 watts of amplifier power and shall have a nominal impedance of 8 ohms. The HF section shall produce a sound pressure level of 104 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 133 dB SPL on axis at 1 meter. It shall handle 200 watts of amplifier power and shall have a nominal impedance of 8 ohms.

The loudspeaker enclosure shall be irregularly trapezoidal in shape. It shall be constructed of exterior grade Baltic birch plywood and shall employ extensive internal bracing. It shall be finished in wear-resistant textured black paint. Input con- nectors shall be 2x Neutrik NL4 Speakon wired in parallel. It shall include a pole mount cup and handles integral to the enclosure. One 11-position fly track and two 3-position fly tracks shall be provided on the top and bottom of the enclo- sure respectively. Four 5/16"-18 threaded mounting points for use with an Omnimount® Series 300 (or similar) shall be pro- vided on the rear of the enclosure. The front of the loud- speaker shall be covered with a foam backed, powder coated perforated steel grille.

The 2-way full-range loudspeaker shall be the EAW model JFX200.

NL 4 MPR			PHYSICAL continued
			Dimensions		inches	millimeters
				Height	22.25	565
				Width (front)	13.68	347
				Width (rear)	4.46	113
				Depth	15.25	387
			Weights		pounds	kilograms
				Net Weight	58	26.4
				Shipping Weight	64	29.1
One Main Street, Whitinsville, MA 01588	508 234 6158	Toll Free 800 992 5013		FAX 508 234 8251	info@eaw.com	www. eaw. com
EAW products are continually improved. All specifications are therefore subject to change without notice.				JFX200/0004639/2 pp	September 2002	Printed in USA