Ericsson LPE-200 manual Options and Accessories, Mechanical

AE/LZB 119 1902 R1A

MECHANICAL

The radios are packaged in a polycarbonate blend exterior housing. A six-cell back mounted nickel cadmium

OPTIONS AND ACCESSORIES

PART NUMBER DESCRIPTION

battery pack provides a nominal 7.5 volts. Two different nickel cadmium battery packs offering high and extended capacities are available for use with the portable radios.

The top of the radio has a Volume, Channel/ Area/System select knob, Emergency/Home button, TX LED and a screw-on antenna mount connector. Located on the front is a 3-line 12 character per line dot matrix LCD with backlighting. A chip-on-glass filtered super twisted nematic LCD with a transflective rear film is used. A 36

BKB 191 203

BKB 191 202

BKB 191 203/A2

BKB 191 202/A2

Batteries

High Capacity NICAD Battery

Extra High Capacity NICAD Battery

High Capacity NICAD Battery (FM Intrinsically Safe)

Extra High Capacity NICAD Battery (FM Intrinsically Safe)

mmspeaker and electret microphone are located above the LCD. Below the speaker is either a 6-button keypad for Scan operation or a 15-button keypad for System operation. A push-to-talk bar is located on the left side along with a Clear/Monitor button and option button. On the opposite side a UDC connector is located for plug-in accessories and PC programming.

One printed wire board assembly contains the transmitter/receiver, audio and logic circuitry. A separate printed wire board assembly (daughter board) contains the DSP Module. The radio board assembly is cradled in a zinc die casting which is used as a PA heat sink and for housing rigidity. A sheet metal shield completes the RF shielding.

The keypad and LCD assembly are separate from the main board and interconnect by a flex-circuit. This flex- circuit also interconnects the speaker, microphone and UDC assemblies. Top controls mount to another flex-circuit board that plugs into the main radio board assembly.

Radio circuitry is centered mainly on one radio board. This board is mounted in a metal housing with a metal shield covering the top of the board. This enclosure is penetrated only by a flex cable which ties the front, user interface part of the radio to the board and a 3-pin battery connector. Surface mount components populate both top and bottom of the radio board allowing a combination of both RF and

		Chargers
BML 161 51/505	120	Volt, Rapid (Ericsson label)
BML 161 51/506	120 Volt, Rapid (GE label)
BML 161 51/507	230	Volt, Rapid (Ericsson label)
BML 161 51/513	120	Volt, Multi Rapid (Ericsson label)
BML 161 51/514	120 Volt, Multi Rapid (GE label)
BML 161 51/515	230	Volt, Multi Rapid (Ericsson label)
		Antenna
KRE 101 1223/02	900 MHz Whip Antenna

Carrying Accessories

KRY101 1605/01		Leather Case With Belt Loop
KRY101 1605/A2		Leather Case W/Swivel And Belt Loop
KRY 101	1609/A1	Belt Loop With Swivel
KRY 101	1232/2	Plastic Belt Clip
KRY 101	1607/1	Leather Shoulder Strap
		Audio Accessories

digital circuits. Only a few leaded parts are used where no surface mount components are available.

KRY 101 1617/1

KRY 101 1617/3 KRY 101 1617/A2 KRY 101 1617/A4

RLD 541 07/11

Speaker Microphone (GE label)

Speaker Microphone (Ericsson label) Speaker Mic., With Antenna (GE label)

Speaker Mic., With Antenna (Ericsson label)

Earpiece Kit, Speaker Microphone

7