RIDGID R8408 manual General Maintenance, Batteries

Page 22

MAINTENANCE

WARNING:

When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING:

To avoid serious personal injury, always remove the battery pack from the product when cleaning or performing any maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a RIDGID authorized service center.

BATTERIES

This product will accept 24 V and 18 V lithium-ion batteries or 18 V, 14.4 V, and 12 V nickel-cadmium batteries. Length of service from each charging will depend on the type of work you are doing.

The batteries for this tool have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.

To obtain the longest possible battery life, we suggest the following:

For lithium-ion batteries:

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F and away from moisture.

Store battery packs in a 30%-50% charged condition.

Every six months of storage, charge the pack as normal.

For nickel-cadmium batteries:

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F.

Store battery packs in a “discharged” condition.

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

To preserve natural resources, please recycle or dispose of batteries properly.

 

This product uses lithium-ion or nickel-

Li - Ion

cadmium batteries. Local, state or federal

 

laws may prohibit disposal of batteries in

 

ordinary trash.

Consult your local waste authority for information regarding available recycling and/or disposal options.

WARNING:

Upon removal, cover the battery pack’s terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Lithium-ion and nickel- cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

22

Image 22
Contents OPERATOR’S Manual Table of Contents IntroductionPersonal Safety General Safety Rules Important Safety InstructionsElectrical Safety Heed ALL Warnings Follow ALL InstructionsSpecific Safety Rules ServiceSymbols Symbol Name DESIGNATION/EXPLANATIONDouble Insulation Cord Length Wire Size A.W.GElectrical Electrical ConnectionProduct Specifications FeaturesFCC Compliance Backlit LCD Display Race ScannerDigital Clock TOP Tray Squelch ControlProtective Steel Roll Cage Unpacking AssemblyOperation Packing ListGeneral Usage Tips Charger and Battery Packs Sold SeparatelyTo install/REPLACE clock/MEMORY batteries CordReceptacle To INSTALL/remove Battery PackLatches Dc 1-amp ReceptacleLCD display WIRE-STYLE FM Antenna OptionalAdjusting the volume Turning the radio on/offManual tuning all modes Mode SelectionSeek/scan AM & FM Modes Storing a preset in Memory Direct tuneBass boost Setting the clockStereo/mono Fm only Bass Boost Hour h Minute mNormal Scan and Preset Scan Modes Race Specific FeaturesPreset Scan Mode Clearing Race Presets To clear a preset Race channel from memorySkipping Frequencies and Presets Squelch controlUsing AN iPod with the Job-site radio/ race scanner 30-pin Connectors IPodLCD Displays UX 2 Mode Battery Pack Removal and Preparation for Recycling MaintenanceGeneral Maintenance BatteriesTrackside Planner Driver/Car No Frequency PresetRace LOCATION/DATE Trackside Planner What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No R8408 Serial No