RIDGID R8408 manual Features, Product Specifications, FCC Compliance

Page 7

FEATURES

PRODUCT SPECIFICATIONS

Operating Temperature

 

 

Normal

32˚F - 104˚F

Frequency Ranges

 

 

AM Band

520-1710 (KHz)

FM Band

87.5 - 108.1

(MHz)

Race Band

(UHF) 450.0375 - 469.9625

(MHz)

Scan Rate (Race Band)

16 Channels per second

Scan Delay

60 Microseconds

Audio Output

 

 

13 Watts nominal into 4 Ω (Ohm) internal speakers

12.5mW nominal into 32 Ω (Ohm) Headphone 25 mW nominal into 64 Ω (Ohm) Earphone

Power Requirements

120 VAC through cord or 12 V DC, 14.4 V DC, 18 V DC, and 24 V DC RIDGID slide-mount batteries

3 AA (1.5 V DC) batteries for memory/clock backup Power Outputs

1 Automotive-type power receptacle, 12 V DC,

1 Amp Max.

External Jacks

 

Antenna Connector

................... For single-wire antenna

Headphone Jack

3.5 mm

iPod Connector

30-pin iPod docking connector

Input Jack

3.5 mm (Inside door)

Size

22 in. (L) x 13 in. (H) x 12 in. (W)

Weight

23.5 lb.

FCC COMPLIANCE

Warning:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen- tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents OPERATOR’S Manual Introduction Table of ContentsHeed ALL Warnings Follow ALL Instructions General Safety Rules Important Safety InstructionsElectrical Safety Personal SafetyService Specific Safety RulesSymbol Name DESIGNATION/EXPLANATION SymbolsElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationProduct Specifications FeaturesFCC Compliance Backlit LCD Display Race ScannerDigital Clock TOP Tray Squelch ControlProtective Steel Roll Cage Packing List AssemblyOperation UnpackingCord Charger and Battery Packs Sold SeparatelyTo install/REPLACE clock/MEMORY batteries General Usage TipsDc 1-amp Receptacle To INSTALL/remove Battery PackLatches ReceptacleTurning the radio on/off WIRE-STYLE FM Antenna OptionalAdjusting the volume LCD displayManual tuning all modes Mode SelectionSeek/scan AM & FM Modes Direct tune Storing a preset in MemoryFm only Bass Boost Hour h Minute m Setting the clockStereo/mono Bass boostNormal Scan and Preset Scan Modes Race Specific FeaturesPreset Scan Mode To clear a preset Race channel from memory Clearing Race PresetsSquelch control Skipping Frequencies and Presets30-pin Connectors IPod Using AN iPod with the Job-site radio/ race scannerLCD Displays UX 2 Mode Batteries MaintenanceGeneral Maintenance Battery Pack Removal and Preparation for RecyclingTrackside Planner Driver/Car No Frequency PresetRace LOCATION/DATE Trackside Planner HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No R8408 Serial No Customer Service Information
Top Page Image Contents