La Crosse Technology WS-7058U instruction manual Hard Reset of Eeprom Weather Center Memory

Page 15

7.Use the + button to change the first digit to a 3 and press the SET button to enter the normal mode. The Weather Center will enter into normal operating mode. Do not press any buttons while the Weather Center searches for transmisssion signals.

8.Follow Program Mode for set-up proceedures.

C.HARD RESET OF EEPROM WEATHER CENTER MEMORY

Note: This is to be used if there are problems with transmission, or if the rainfall history bar graph needs to be cleared.

1.Remove the batteries and wait 30 seconds. (This will also reset the Rainfall Quantity Totals).

2.Checking the polarity, install batteries.

3.During the brief 2 seconds that all LCD screens light up, simultaneously press and hold the RAIN and + buttons.

“375” (the default rain multiplicator setting) will appear in LCD 1. The “5” will be flashing.

If “375” does not appear, it will be necessary to set the manually set the digits. Use the + button to change the digit, and the SET button to select the digit to be changed.

4.Press the SET button two times. (The 3 should flash).

5.Hold the SET button down until the air pressure (in hPa) briefly flashes in LCD 5. “LCD 5” will flash in LCD 2 for 15 seconds.

6.Do not press any buttons while the Weather Center searches for transmission signals.

7.Follow Program Mode for set-up proceedures.

VII. ADDING MORE SENSORS (optional)

The WS-7058U can receive signals from up to three Sensors. The Sensor model(s) that you choose will come with their own set of instructions—follow those instructions for a complete guide to setting up. Following are some brief instructions for the basic set-up of additional sensors with the WS-7058U. Additional sensors can be purchased through the same dealer as this Weather Center, or by contacting La Crosse Technology directly (contact information can be found at the end of this manual). A TX4U will monitor temperature and humidity (it is the same model that comes with the WS-7058U), a TX3U will monitor temperature only, and the TX3UP monitors temperature via a 10 foot probe for use in pools, spas, etc. The TX3 units do not monitor humidity, thus when they transmit their information to the Weather Center dashes “- -” appear in the Humidity Display.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents WS-7058U Wireless 433 MHz Wireless Weather Center Table of Contents Quick SET-UP Guide Inventory of ContentsDetailed SET-UP Guide Battery Installation Remote THERMO-HYGRO SensorRainfall Sensor LCD Screen Weather CenterFunction Buttons Program ModeII. Setting the LCD Contrast IV. Time SettingTime Zone Setting VI. Date SettingVII. Selecting F or C and Inches or Millimeters IX. Displaying Relative hPa/inHg or Absolute hPa/inHg VIII. Weather Forecast Sensitivity SettingManually Setting the Relative AIR Pressure II. Minimum & Maximum Temperatures Displays and FunctionsXI. Selecting BAR Graph Display III. Weather Forecast & Weather Icons Resetting the Minimum & Maximum RecordsWeather Icons Weather Tendency ArrowsStorm Warning IV. BAR Graph Histories AIR Pressure History Comfort Level IndicatorRainfall Quantity Rainfall HistoryManual Setting of the Rain Multiplicator VI. Resetting Rainfall Information Rainfall Quantity TotalsVII. Adding More Sensors optional Hard Reset of Eeprom Weather Center MemorySET-UP of Multiple Sensors Selecting Which Sensor Data to DisplayMounting TX4U-REMOTE THERMO-HYGRO Sensor Mounting with the ScrewsMounting with Adhesive Tape II the TX5U-RAINFALL Sensor III the WS-7058U-WEATHER Center Table StandWall Mounting Solution Maintenance and CareTroubleshooting ProblemAir pressure Temperature measuring rangeSensor reading update Relative humidity rangeDimensions L x W x H Power supplyWarranty Information Support@lacrossetechnology.com
Top Page Image Contents