Bard Q48A1, Q30A1, Q36A1, Q42A1, Q60A1 Duct Work, Filters, Supply Duct Connections, Filter Location

Page 11

DUCT WORK

All duct work must be properly sized for the design airflow requirement of the equipment. Air Conditioning Contractors of America (ACCA) is an excellent guide to proper sizing. All duct work or portions thereof not in the conditioned space should be properly insulated in order to both conserve energy and prevent condensation or moisture damage. When duct runs through unheated spaces, it should be insulated with a minimum of one inch of insulation. Use insulation with a vapor barrier on the outside of the insulation. Flexible joints should be used to connect the duct work to the equipment in order to keep the noise transmission to a minimum.

The Q-TECseries unit has provision to attach a supply air duct to the top of the unit. Duct connection size is 12 inches x 20 inches. The duct work is field supplied and must be attached in a manner to allow for ease of removal when it becomes necessary to slide the unit out from the wall for service. See Figure 7 for suggested attachment method.

The Q-TECseries units are designed for use with free return (non-ducted) and either free blow with the use of QPB Plenum Box or a duct supply air system.

The QPB and QPBHW Plenum Box mounts on top of the unit and has both vertically and horizontally adjustable louvers on the front discharge grille.

For hot water coil option a QPBHWxx-F for free blow or QPBHWxx-D for ducted airflow is used.

FIGURE 7

SUPPLY DUCT CONNECTIONS

SUPPLY DUCT

TO BE FIELD

SUPPLIED

ATTACHMENT

SCREWS TO

BE FIELD

SUPPLIED

ROOM SIDE OF Q-TECUNIT

DUCT FLANGE

PROVIDED WITH UNIT

NOTE: Unit cabinet, supply air duct and free blow plenum are approved for “0” clearance to combustible material.

When used with a ducted supply, a QCX Cabinet Extension can be used to conceal the duct work above the unit to the ceiling. This extends 20" above the unit for a total height above the floor of 10'-7/8". The unit is equipped with a variable speed indoor blower motor which increases in speed with an increase in duct static pressure. The unit will therefore deliver proper rated airflow up to the maximum ESP shown in Table 7. However, for quiet operation of the air system, the duct static should be kept as low as practical, within the guidelines of good duct design.

FILTERS

Two 1-inch throw away filters [(1) 16x16 and (1)

16x20] are supplied with each unit. The filters slide into filter brackets. Refer to Figure 8.

The filters are serviced from the inside of the building by opening the hinged door. This door is attached by a screw and one locking latch.

The internal filter brackets are adjustable to accommodate 2-inch filters. The tabs for the 1-inch filters must be bent down to allow the 2-inch filters to slide in place.

FIGURE 8

FILTER LOCATION

FILTERS

RETURN AIR

GRILLE

Manual

2100-522B

Page

11 of 38

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Models Contents For More INFORMATION, Contact These Publishers Getting Other Information and PublicationsTecmodel Nomenclature TECSeries General InformationFactory BUILT-IN Electric Heat Table Electrical Specifications Unit Dimensions Removal of Unit from Skid Shipping DamageUnit Removal from Skid AIR Seal Under Qtec UnitUnit on Appliance Cart Minimum Installation HeightHandling Unit After Removal from Skid GeneralInstallation with Free Blow Plenum Ducted Application Filter Location Duct WorkFilters Supply Duct ConnectionsOptional Rear Drain Kits Service LightFresh AIR Intake Condensate DrainStandard Rear Drain Rear Drain TOP View Optional Side Drain Side View InstallationWall Sleeve Plug Installed If Used MIS-2472 Unit Mounting Removing Locking Screws from Wheels Installation InstructionsMounting the Unit Operating Voltage Range Wiring Main PowerWiring LOW Voltage Wiring Component LocationLOW Voltage Connections For DDC Control LOW Voltage ConnectionsWall Thermostats Thermostat Predominant FeaturesThermostat Option Remote Thermostat Wiring DiagramThermostat Option Unit Mounted Thermostat Wiring Diagram Thermostat Option8403-060 Plug #2 Orange Purple Brown/White Yellow Blue Red Red/White Black Black/White Yellow Brown Topping OFF System Charge Safety PracticesStart UP Description of Standard Equipment Important Installer NotePhase Monitor Three Phase Scroll Compressor Start UP InformationCompressor Control Module Service HintsEconomizer or Commercial Room Mist Eliminator ServiceVent Options Option Tecenergy Recovery VentilatorFresh AIR Damper Removal Qerv Removal CO2 Controller Factory SET to PPM Pressure Service PortsSequence of Operation Optional Climate Controls Sequence of OperationDon’t Troubleshooting GE ECM MotorsReplacing ECM Control Module Troubleshooting GE ECM Motors CONT’DRefrigerant Charge FAN Blade Setting DimensionsFAN Blade Setting FAN Blade DimensionsModel Temp Pressure Cooling Pressure ALL Temperatures in Degrees F

Q48A1, Q24A1, Q60A1, Q42A1, Q36A1 specifications

The Bard Q60A1, Q48A1, Q30A1, Q36A1, and Q42A1 are innovative medical devices designed for versatile applications in various healthcare settings. These models are known for their adaptability, precision, and advanced technologies, making them essential tools for healthcare professionals.

The Q60A1 model stands out due to its user-friendly interface and high-resolution display. It is equipped with advanced sensors that provide real-time monitoring and feedback. The device's portability allows it to be easily moved between different areas of a facility, making it ideal for both inpatient and outpatient services. The Q60A1 also integrates seamlessly with electronic health records, enabling better data management and streamlined clinical workflows.

The Q48A1 model emphasizes flexibility and customization. With multiple configurations, this device is adept at accommodating a range of medical procedures. Its modular design allows healthcare providers to adjust the setup to meet their specific needs, enhancing both efficiency and patient comfort. The Q48A1 is favored for its rapid setup time, facilitating quick responses in critical situations.

In contrast, the Q30A1 prioritizes compactness without sacrificing functionality. This device is specifically engineered for smaller spaces, making it a perfect fit for clinics and smaller hospitals. Despite its size, the Q30A1 boasts a robust set of features, including wireless connectivity and the ability to store a significant amount of patient data. Its intuitive controls simplify operation, even for those with minimal training.

The Q36A1 model is notable for its durability and resilience in challenging environments. Constructed with high-grade materials, it withstands wear and tear while maintaining precise performance. The Q36A1 also includes advanced safety features, such as automatic shut-off mechanisms, which ensure safe operation in emergency conditions. Its reliability makes it a trusted choice across various healthcare sectors.

Lastly, the Q42A1 model focuses on user experience, combining technology with ease of use. It is equipped with voice-activated controls and touch-sensitive displays, streamlining interaction for medical staff. This model also features advanced data analytics tools, providing insights that can drive improvements in patient care.

Overall, the Bard Q60A1, Q48A1, Q30A1, Q36A1, and Q42A1 reflect the latest advancements in medical technology, each serving unique functions suited to different healthcare needs. These devices not only enhance operational efficiency but also improve patient outcomes through better monitoring and data management capabilities.
Top Page Image Contents