Friedrich SH15 operation manual Typical Installation

Page 15

STEP 3 Slide the cabinet into the hole far enough to allow the guide-channel of the sill plate to contact the inside wall surface (See Figure O).

STEP 4 Drill three (3) 5/32" diameter pilot holes through holes in sill-plate into the framing and install three (3) #12 x 2" long screws (Item #4) (See Figure O).

NOTICE

Instructions for mounting sleeve with slope must be observed to prevent entry of water into room.

Potential property damage can occur if instructions are not followed.

FIGURE O

TYPICAL INSTALLATION

TRIM MOULDING

CAULK ALL SIDES AIR TIGHT

 

 

3/8" (10 MM) SLOPE DOWN

 

NOTE: SUPPORT BRACKETS MAY BE OMITTED FROM

SCREW #12A X 2" LONG

THROUGH-THE-WALLINSTALLATIONSIFTHECABINETIS

SECURED AS FOLLOWS. DRILL 2 HOLES IN EACH SIDE

USE 3

AND INSTALL 4 FASTENERS (2 EACH SIDE).

 

 

USE #12A X 2" (51 MM) SCREWS, TOGGLE BOLTS OR

 

EXPANSION ANCHOR BOLTS AS SHOWN IN STEP 5.

SILL PLATE GUIDE CHANNEL

 

 

SUPPORT BRACKETS (ITEM 1) (SEE NOTE ABOVE)

INSIDE WALL SURFACE

SCREW #12 X 2" LONG, USE ONE IN EACH

BRACKET. DRILL 5/23 (4 MM) DIA. PILOT HOLES.

 

NOTE: ALTERNATE FASTENERS WHICH MAY BE USED FOR SECURING THE SILL PLATE IN THE WALL, AND THE SUPPORT BRACKETS TO THE OUTSIDE WALL ARE NOT FURNISHED, BUT ARE AVAILABLE AT A LOCAL HARDWARE STORE.

MOLLY OR TOGGLE BOLT

EXPANSION ANCHOR BOLT

STEP 5 Drill two (2) 5/32" (4 mm) dia. pilot holes in each side at the locations shown (Figure O) and install four (4) #12 x 2" screws (Item #4). If the hole construction in Step 2 provides a sturdy mount with solid vertical studs, no support brackets are required. The installation must support the weight of the unit plus an additional weight of 400 pounds (185 kg) on the rear of the cabinet. The support brackets may be used for through-the-wall installations as shown in Figure O, for additional support.

STEP 6 If desired, trim around the cabinet on the room side with a suitable frame molding furnished by the installer (See Figure O).

15

Image 15
Contents Volt SH15 SH20 Hazardous Duty Room Air ConditionerTable of Contents Congratulations Filter Information Maintenance ChecklistControl Panel Hazardgard Special FeaturesFunction Control Power Temperature ControlModels SH15 and SH20 Electrical RequirementsGroups Accessory Detail Window Mount Installation HardwareChassis Wiring and Preparation Unpacking The UnitProvided Hardware Before Shell Cabinet PreparationFalling Object Hazard Shell Installation Sash Window InstallationsShell Installation Thick Wall Section B B Section a aShell Installation Through-the-wall Installations Wall PreparationSpecial Instructions For Extra Thick Walls Frame Wall Construction Typical Installation Excessive Weight Hazard Chassis InstallationDetail Hazardgard Room AIR Conditioners Limited Warranty Unidades de aire acondicionado Tabla DE Contenidos Aviso Lista De Control Para El Mantenimiento Informacion Sobre El FiltroControl De La Temperatura Caracteristicas Especiales Del HazardgardPanel De Control Control De Encendido Electricidad¡EXCLUSIVA Modelos SH15 y SH20 Requerimientos ElectricosGrupos Tamaño DEL Gabinete Número Descripción Cantidad De item Lista DE AccesoriosDesempaque de la unidad Preparacion y Instalacion Electrica Del ChasisHerramienta QUE SE Suministra Antes Si la instalacion se hace a traves de la paredFigura D Instalacion Tipica Del Filo Del Antepecho Industrial, para prevenir que haya !ltración de agua Nota Estas SON LAS Dimensiones DEL Hueco Terminado Dimension Chasis TerminadaParedes DE Ladrillo Construccion EN ELMarco DE LA Pared Construccion ENFigura O Instalacion TipicaFigura P Instalacion DEL ChasisFigura Q DetalleFriedrich Air Conditioning Company Climatiseurs Instructions D’UTILISATION ET D’ENTRETIEN Table DES MatièresTous nos compliments Dépannage Caractéristiques Spéciales Des Appareils Hazardgard Panneau De CommandeCommande De Fonction Mise En Marche Commande De TempératureExclusivité Modèles SH 15 et SH Alimentation ÉlectriqueGroupes Détail DES Accessoires Déballage De L’appareil Branchement Du Châssis Et PréparationQuincaillerie Fournie Avant Après Installation dans une fenêtre à guillotineInstallation à travers un mur Préparation De L’enveloppeFigure D Installation Typique De La Plaque De Seuil Coupe B B Installation De Lenveloppe Installation À Travers Un Mur Dimensions Finies DE L’OUVERTUREPréparation Du Mur UN Cadre EN Bois Boulon DE Scellement InstallationtypiqueInstallation DU Châssis Figure Q DétailGarantie Limite DUN AN Climatiseurs Hazardgard Friedrich Page Page Page Friedrich AIR Conditioning CO
Related manuals
Manual 56 pages 18.6 Kb

SH15 specifications

The Friedrich SH15 and SH20 models are exemplary representatives of advanced heating solutions, designed to address the diverse needs in residential and commercial environments. Engineered with a focus on efficiency, performance, and user-friendliness, these heating systems make a strong case for modern heating technology.

One of the standout features of both the SH15 and SH20 is their energy efficiency. These models utilize state-of-the-art heat pump technology, which allows them to extract heat from the environment even in colder temperatures. This results in significantly lower energy consumption compared to traditional heating systems, leading to reduced utility bills and a lower carbon footprint. The SH15 is designed for smaller spaces, while the SH20 offers a bit more power, making it suitable for larger areas or homes with greater heating demands.

Both models incorporate advanced inverter technology, which adjusts the compressor speed depending on the heating requirements. This ensures that the units operate at optimal efficiency, providing consistent temperature control while minimizing energy waste. Inverter-driven systems contribute to quieter operation as well, which is ideal for residential settings where noise can be a concern.

User-friendliness is another hallmark of the Friedrich SH15 and SH20. Equipped with intuitive digital controls, users can easily set their preferred temperatures and schedules, allowing for personalized comfort. Moreover, both models support smart home integration, enabling remote access and control through mobile applications. This feature not only enhances convenience but also allows users to monitor energy usage and make adjustments on the fly.

Durability is a key characteristic of these heating systems. Constructed with high-quality materials, the SH15 and SH20 are designed to withstand harsh environmental conditions, ensuring long-lasting performance. They also feature advanced air filtration systems that improve indoor air quality by effectively removing allergens and other pollutants.

In summary, the Friedrich SH15 and SH20 embody the cutting-edge of heating technology, offering powerful, efficient, and user-friendly solutions for diverse heating needs. With their advanced features, smart technology integration, and robust construction, these models are well-suited for modern living, ensuring comfortable and environmentally responsible heating year-round.