Friedrich SH15 operation manual Shell Installation Thick Wall

Page 11

Shell Installation: Thick Wall

The illustrations below show a standard frame construction installation as well as some suggested ways of adapting the support bracket to thick walls and large brick ledges.

NOTICE

Instructions for mounting sleeve with slope must be obser- ved to prevent entry of water into room.

Failure to follow instructions can result in property damage.

Typical Installation Sill Plate

 

 

 

 

FIGURE 1

FIGURE 2

 

10 - 24 SCREW

 

 

10 - 24 FLAT NUT

 

3/8" (10 MM)

 

 

3/8" (10 MM)

 

SLOPE DOWN

 

 

SLOPE DOWN

 

 

 

CUT

 

 

HERE

 

WOOD

 

 

LEDGE

 

STONE LEDGE

#12A X 2" SHEET METAL SCREW

 

OUTSIDE WALL

1" X 2" OR 2" X 4" SPACER BETWEEN WALL

DISCARD

CUT TO FIT DIMENSION "A"

AND BEND DOWN TO FOR A

AND BRACKET SHOULD BE USED ON ALU-

SHADED AREA

VERTICAL LEG

MINUM, ASBESTOS OR VINYL SIDING

 

 

 

 

 

 

FIGURE 3

FIGURE 4

 

BRICK LEDGE

STONE LEDGE

 

 

3/8" (10 MM)

 

3/8" (10 MM) SLOPE DOWN

SLOPE DOWN

 

 

 

 

STRAIGHTEN TAB TO LAY FLAT ALONG

#12A X 2" SHEET METAL SCREW

 

THE BOTTOM RAIL OF THE SHELL.

 

 

 

 

SECURE THE LONGEST SIDE OF

 

 

THE BRACKET TO THE SHELL.

2" X 4" SPACER

 

ADJUST IN OR OUT TO

 

 

 

 

REST ON THE LEDGE

 

 

 

STEP 4 CUT WINGBOARD PANELS: Measure and cut the wingboard panels from the supplied masonite (Item #8) to !t the spaces between the side window channels and the sides of the cabinet (See Figure F).

NOTE: AFTER CUTTING PANELS, MAKE A TRIAL TEST TO SEE IF THEY FIT THE SPACE WITH ABOUT 1/8" CLEARANCE BEFORE GOING TO STEP 5.

FIGURE F

MEASURE DISTANCE "B" TO THE INSIDE

OF THE CHANNEL ON EACH SIDE

CUT HERE AND DISCARD THE CENTER

WASTE MATERIAL

WINGBOARD

SUBTRACT 1/8" (3 MM) FROM DIMENSION "B" AND MEASURE FROM THE EDGE OF THE WINGBOARD (ITEM

# 8), MARK AND CUT WITH A SAW.

11

Image 11
Contents Volt SH15 SH20 Hazardous Duty Room Air ConditionerTable of Contents Congratulations Filter Information Maintenance ChecklistControl Panel Hazardgard Special FeaturesFunction Control Power Temperature ControlGroups Models SH15 and SH20Electrical Requirements Accessory Detail Window Mount Installation HardwareProvided Hardware Chassis Wiring and PreparationUnpacking The Unit Before Shell Cabinet PreparationFalling Object Hazard Shell Installation Sash Window InstallationsShell Installation Thick Wall Section B B Section a aSpecial Instructions For Extra Thick Walls Shell Installation Through-the-wall InstallationsWall Preparation Frame Wall Construction Typical Installation Excessive Weight Hazard Chassis InstallationDetail Hazardgard Room AIR Conditioners Limited Warranty Unidades de aire acondicionado Tabla DE Contenidos Aviso Lista De Control Para El Mantenimiento Informacion Sobre El FiltroControl De La Temperatura Caracteristicas Especiales Del HazardgardPanel De Control Control De Encendido Electricidad¡EXCLUSIVA Grupos Tamaño DEL Gabinete Modelos SH15 y SH20Requerimientos Electricos Número Descripción Cantidad De item Lista DE AccesoriosHerramienta QUE SE Suministra Desempaque de la unidadPreparacion y Instalacion Electrica Del Chasis Antes Si la instalacion se hace a traves de la paredFigura D Instalacion Tipica Del Filo Del Antepecho Industrial, para prevenir que haya !ltración de agua Nota Estas SON LAS Dimensiones DEL Hueco Terminado Dimension Chasis TerminadaParedes DE Ladrillo Construccion EN ELMarco DE LA Pared Construccion ENFigura O Instalacion TipicaFigura P Instalacion DEL ChasisFigura Q DetalleFriedrich Air Conditioning Company Climatiseurs Instructions D’UTILISATION ET D’ENTRETIEN Table DES MatièresTous nos compliments Dépannage Caractéristiques Spéciales Des Appareils Hazardgard Panneau De CommandeCommande De Fonction Mise En Marche Commande De TempératureExclusivité Groupes Modèles SH 15 et SHAlimentation Électrique Détail DES Accessoires Quincaillerie Fournie Déballage De L’appareilBranchement Du Châssis Et Préparation Avant Après Installation dans une fenêtre à guillotineInstallation à travers un mur Préparation De L’enveloppeFigure D Installation Typique De La Plaque De Seuil Coupe B B Préparation Du Mur Installation De Lenveloppe Installation À Travers Un MurDimensions Finies DE L’OUVERTURE UN Cadre EN Bois Boulon DE Scellement InstallationtypiqueInstallation DU Châssis Figure Q DétailGarantie Limite DUN AN Climatiseurs Hazardgard Friedrich Page Page Page Friedrich AIR Conditioning CO
Related manuals
Manual 56 pages 18.6 Kb

SH15 specifications

The Friedrich SH15 and SH20 models are exemplary representatives of advanced heating solutions, designed to address the diverse needs in residential and commercial environments. Engineered with a focus on efficiency, performance, and user-friendliness, these heating systems make a strong case for modern heating technology.

One of the standout features of both the SH15 and SH20 is their energy efficiency. These models utilize state-of-the-art heat pump technology, which allows them to extract heat from the environment even in colder temperatures. This results in significantly lower energy consumption compared to traditional heating systems, leading to reduced utility bills and a lower carbon footprint. The SH15 is designed for smaller spaces, while the SH20 offers a bit more power, making it suitable for larger areas or homes with greater heating demands.

Both models incorporate advanced inverter technology, which adjusts the compressor speed depending on the heating requirements. This ensures that the units operate at optimal efficiency, providing consistent temperature control while minimizing energy waste. Inverter-driven systems contribute to quieter operation as well, which is ideal for residential settings where noise can be a concern.

User-friendliness is another hallmark of the Friedrich SH15 and SH20. Equipped with intuitive digital controls, users can easily set their preferred temperatures and schedules, allowing for personalized comfort. Moreover, both models support smart home integration, enabling remote access and control through mobile applications. This feature not only enhances convenience but also allows users to monitor energy usage and make adjustments on the fly.

Durability is a key characteristic of these heating systems. Constructed with high-quality materials, the SH15 and SH20 are designed to withstand harsh environmental conditions, ensuring long-lasting performance. They also feature advanced air filtration systems that improve indoor air quality by effectively removing allergens and other pollutants.

In summary, the Friedrich SH15 and SH20 embody the cutting-edge of heating technology, offering powerful, efficient, and user-friendly solutions for diverse heating needs. With their advanced features, smart technology integration, and robust construction, these models are well-suited for modern living, ensuring comfortable and environmentally responsible heating year-round.