Friedrich PTAC External Drain for new construction or unit replacement, Drain Kit Installation

Page 6

920-087-02 (9-03)

External Drain (for new construction or unit replacement)

When using an external drain system, the condensate is removed through either of two drain holes on the back of the wall sleeve. Select the drain hole which best meets your drainage situation and install the drain kit. Seal off the other with a cover plate.

Drain Tube Installation

Cover Plate Installation

1.Peel the backing tape off the gaskets and apply the sticky side to one cover plate and one mounting plate as shown in Details A and B.

2.Place the drain tube through the gasket and the mounting plate with the flange toward the wall sleeve.

3.Attach the drain tube assembly to one of the two drain holes at the rear of the wall sleeve. The large flange on the mounting plate is positioned at the bottom of the sleeve facing toward the sleeve, Detail B. When the drain tube is positioned at the desired angle, tighten the screws.

NOTE: If the wall sleeve has not been installed, the drain tube must be rotated to a horizontal position until after the sleeve is installed. Tighten the mounting plate screws when the tube is in the proper position. Make certain that the four overflow slots at the rear of the wall sleeve are not blocked. (See the drawing below.)

4.Mount the foam gasket to the cover plate. Using two #10 x 1/2" sheet metal screws (provided), attach the cover plate to the remaining drain hole. Make certain the large flange on the plate is positioned at the bottom of the sleeve.

5.Discard the additional cover plate, gasket, machine screws, and locknuts.

PXDR1O

QUANTITY

DESCRIPTION

2COVER PLATES

1MOUNTING PLATE

1DRAIN TUBE

3MOUNTING PLATE GASKETS

4#10 X 1/2" MOUNTING SCREWS

210-24 X 1/2" MACH. SCREWS

2LOCKNUTS

Figure 4

Drain Kit Installation

Foam gasket

Mounting plate

DETAIL A

Foam gasket

1/2" O.D. tube

Mounting plate

#10 sheet metal screws

DETAIL B

NOTES:

The large flange on the mounting plate is positioned at the bottom of the sleeve facing toward the sleeve. The drain tube must be rotated to a horizontal position to allow for the wall sleeve to be installed into the wall. Once the wall sleeve is installed, return the drain tube to a downward angle.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents WallMaster Ptac Standard Remote Thermostat Seacoast ProtectedTable of Contents Typical Unit ComponentsModel Number Code Ptac Installation Recommendations Building ElevationInstallation Instructions PXDR10 Drain Kit Drain Kit Location and InstallationInternal Drain optional for new construction Drain Tube Installation Cover Plate Installation External Drain for new construction or unit replacementDrain Kit Installation PXDR1OWall Sleeve Installation Instructions Pxws Typical Wall Sleeve InstallationDimensions Lintel InstallationSection II Deep Wall Installation Pxwe Extension InstallationWall Sleeve Extension Sealant Locations Installation Instructions Model Pxga Standard Grille Standard GrilleInstallation Checklist Electrical Rating TablesSection III Chassis Installation Suffocation hazard Keep bag away from babies and childrenScrew clips Chassis Mounting screw Chassis flange Standard Unit Control Panel Temperature Limiting ThermostatStandard Unit Operation Cooling only Model HEAT/COOL ModelFan Cycle Switch Heating Control heat pumps and emergency heat operationFresh Air Vent Control Start-up Checklist Air Discharge GrilleManual Changeover Thermostat Appendix a Remote Thermostat Unit InstallationSimplified Wiring Example Honeywell Thermostat Terminal DesignationRemote Thermostat 208V Operation Remote Thermostat InstallationAppendix a Auto Changeover ThermostatAppendix B Electrical Wiring for 265 Volt Models Line Voltage ConnectionsRoutine Maintenance Basic Troubleshooting Techniques Maintenance and Inspection Troubleshooting GuideFriedrich Ptac Accessories Model Number Description PhotoModel Number Description DesignatordescriptionRevised 8/01

PTAC specifications

Friedrich PTAC (Packaged Terminal Air Conditioner) units are a popular choice for heating and cooling in commercial and residential spaces, thanks to their efficient design and reliable performance. Friedrich, a company with a long-standing reputation in the HVAC industry, offers a range of PTAC units characterized by advanced features and technologies that set them apart from traditional cooling systems.

One of the main features of Friedrich PTAC units is their high energy efficiency. Many of their models are Energy Star certified, which means they meet the stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency. This efficiency translates into lower energy costs for users and reduced environmental impact, making them an excellent choice for energy-conscious consumers.

Friedrich PTAC units are equipped with advanced technologies that enhance their functionality. For instance, many units come with a built-in Wi-Fi option, enabling remote control through mobile devices. This feature allows users to monitor and adjust temperature settings, schedules, and modes from anywhere, providing convenience and ensuring energy is not wasted when spaces are unoccupied.

The design of Friedrich PTAC units also emphasizes ease of installation and maintenance. These units are designed to fit into existing wall sleeves, making replacement straightforward without significant structural modifications. Furthermore, their ease of access for servicing ensures that maintenance tasks can be performed quickly, reducing downtime and improving longevity.

Another key characteristic of Friedrich PTAC units is their robust construction. Built to withstand varying conditions, these units feature durable materials that ensure long-term reliability. Many models incorporate advanced sound-dampening technology, creating a quieter operation that enhances comfort, especially in residential applications.

Friedrich’s commitment to innovation is evident in its product line, offering various options to meet different climate requirements and user preferences. The units can provide both heating and cooling, making them versatile for year-round use. Additionally, they are available in various BTU capacities, allowing customers to select the appropriate model for their specific space needs.

Overall, Friedrich PTAC units are recognized for their efficiency, technological advancements, ease of installation, and sturdy design, making them an excellent choice for both commercial and residential applications where reliable climate control is needed.
Top Page Image Contents