Lincoln Electric SVM154-A service manual Welding Sparks can cause fire or explosion, Iii

Page 4

iii

 

SAFETY

 

iii

Return to Master TOC

Return to Master TOC

Return to Master TOC

WELDING SPARKS can cause fire or explosion.

6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire. Remember that welding sparks and hot

materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even though they have been “cleaned”. For information, purchase “Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society (see address above).

6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate cir- cuits. This can create fire hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

CYLINDER may explode if damaged.

7.a. Use only compressed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

Away from areas where they may be struck or subjected to physical damage.

A safe distance from arc welding or cutting operations and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered equipment.

8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturer’s recommendations.

Return to Master TOC

Mar ‘95

Image 4
Contents SVM154-A ISAFETYi Safety Fumes and GasesWelding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Installation Table of Contents Installation SectionTechnical Specifications LN-10 Head & Control General DescriptionSafety Precautions Installation of the LN-10 Boom Mount Wire Feeder ComponentsMounting the 10 Series Wire Drive Recommended Processes and EquipmentConnecting Wire Drive Unit to Control Box Mounting Synergic 7F Wire Drive Unit K679-1 orMounting the LN-10 Control Box Wire Drive Speed Range Selection Control Speed Range SettingSeries Wire Drive Ratio Selection Electrode RoutingWire Feed Drive Roll Kits Procedure to Install Drive Roll and Wire GuidesSeries Wire Drive Roll Kit Installation KP1505 and KP1507 Synergic 7F Wire Drive 4-Roll Kits KP655 and KP656GUN and Cable Assemblies with Standard Connection GUN and Cable Assemblies with FAST-MATE ConnectionGmaw Guns Innershield Guns8INSTALLATIONA-8 Series Wire Drive Water Connections for Water Cooled GunsCylinder may explode if damaged Buildup of Shielding GAS may harm health or killElectrical Installation Input Cable LN-10 Control to Power SourceOptional Features Installation Boom and Bench ConversionsMaterials Required for bench to boom conversion Materials Required for boom to bench conversionTable of Contents Operation Section OperationLN-10 Control DIP Switch Setup Setting the DIP SwitchesWire Drive Head Selection Setup DIP Switch AccessWelding Power Source Selection Step Trigger Mode Operation Selection Security Mode SelectionMetric/English Wire Feed Speed Display Selection S2 switch 1 on = m/minMaximum Limits Setting Mode Selection S2 switch 4 on = Robotics mode onS2 switch 6 on Minimum Limits Setting mode on S2 switch 4 OFF = Robotics mode OFF As shippedPower-Down Save Procedure Lights Indicate whichKeypad and Display Operation Keypad and Display DescriptionTrigger Mode Selection Display Control Keys Control Control Select key enables operator to Digital Memory VoltmeterMaximum and Minimum Limits Setting Modes Dual Procedure Remote Wire Reel Loading READI-REELS Spools or CoilsFigure B.2 GAS Guard Regulator Setting Procedure for Setting Angle of FeedplateMaking a Weld Wire Reel Changing Wire Feed Overload ProtectionGrounding Lead Protector DH-10Explanation of Prompting Error Messages Display Prompt or ErrorAccessories Table of Contents Accessories SectionTable C.1 LN-10 Wire Feeder Accessories GeneralWire Size Solid Steel Electrode Cored ElectrodeAluminum Electrode Aluminum Electrode For use with Binzel Guns OnlyK683-1 Dual Procedure Switch K683-3 Dual Procedure SwitchK1449-1 Dual Procedure Input Cable AssembliesK1558-1 Remote Switch Interface Module GUN Adapters for 10 SeriesGUN and Cable Assemblies K1561-1 Robotics Interface ModuleK1556-1 Light Duty Caster KIT K1557-1 Swivel MountK1555-1 Insulated Lift Hook Maintenance Table of Contents Maintenance SectionMaintenance Avoiding Wire Feeding Problems Safety PrecautionsRoutine Maintenance Periodic MaintenanceFigure D.1 Major Component Locations Table of Contents Theory of Operation Section Theory of OperationControl Board Input RECEPTACLE, Control Board and Operator Controls Wire Feed Head Receptacle Figure E.3 LN-10 Wire Feed Head and ReceptacleWire Feed Overload Loss of Voltage Sense Protection Shutdown Theory of Operation Protection and ShutdownLN-10 Troubleshooting and Repair Table of Contents Troubleshooting and Repair SectionHOW to USE Troubleshooting Guide Return to Return to Master TOCPC Board Troubleshooting Procedures LN-10 Troubleshooting Guide Function ProblemsFunction Problems Power Source Selection Function Problems Mode Selection Perform the Encoder Board Test Troubleshooting and Repair Mum and minimum limit set Perform the Gas Solenoid Test Feeding Problems Welding Problems LN-10 Test Procedures Wire Drive Motor TestTest Description Materials NeededWire Drive Motor Test Test ProcedureTach Adjustment and Feedback Test Materials Needed20TROUBLESHOOTING and REPAIRF-20 Tach Adjustment and Feedback TestTach Adjustment Procedure LN-10 Keypad Resistance Test 24TROUBLESHOOTING and REPAIRF-24 Keypad Resistance TestControl Ohms 50 Ohms Typical LN-10 Encoder PC Board Test Encoder PC Board Test Figure F.4 Encoder PC Board TestGAS Solenoid Test 30TROUBLESHOOTING and REPAIRF-30 GAS Solenoid TestComponent Replacement Procedures Display PC Board Removal and Replacement32TROUBLESHOOTING and REPAIRF-32 Display PC Board Removal and ReplacementRemoval Procedure Replacement ProcedureGAS Solenoid Removal and Replacement 34TROUBLESHOOTING and REPAIRF-34 GAS Solenoid Removal and ReplacementEncoder PC Board Removal and Replacement Encoder PC Board Removal and Replacement Figure F.8 Encoder PC Board Removal and ReplacementWire Drive Motor and Gear BOX Removal and Replacement Wire Drive Motor and Gear BOX Removal and Replacement Figure F.9 Wire Feed Assembly RemovalTo Remove the Wire Drive Assembly from the Gear BOX To Remove the Drive Motor from the Gear BOXReplacement Procedures Current Sensing Reed Switch Removal and Replacement Current Sensing Reed Switch Plug Check Wire Feed Speed Range Retest After RepairElectrical Diagrams Section Electrical Diagrams Wiring Diagram LN-10 ControlWiring Diagram LN-10 Wire Drive Electrode Cable From Current SensorSchematic Control PC Board #1 Schematic Control PC Board #2 Circuitry TachPC Board ASSEMBLY-CONTROL 3168 GSchematic Display PC Board 5VABoard Schematic Encoder PC Board 22066PC Board ASSEMBLY-ENCODER EncoderSVM Error Reporting Form

SVM154-A specifications

The Lincoln Electric SVM154-A is a powerful and versatile inverter-based welding machine designed for a wide range of applications. As a part of Lincoln Electric's esteemed portfolio, this model is particularly favored for its robust performance and cutting-edge technologies, making it ideal for both professional fabricators and hobbyists alike.

One of the standout features of the SVM154-A is its compact and lightweight design, which enhances portability without compromising power. Weighing significantly less than traditional welding machines, it allows welders to easily transport the equipment to various job sites. This feature is particularly beneficial in industries where mobility is essential.

Equipped with advanced inverter technology, the SVM154-A delivers a stable and smooth arc, providing consistent welding performance even in challenging conditions. The inverter design also contributes to energy efficiency, allowing users to save on operational costs while enjoying superior performance. The machine supports both MIG and TIG welding processes, which adds to its versatility. This adaptability makes it suitable for a range of materials including mild steel, stainless steel, and aluminum.

Another notable characteristic is its user-friendly interface. Designed with the welder in mind, the SVM154-A includes intuitive controls that simplify settings adjustments and operational processes. This ergonomic layout allows for ease of use, even for beginners, while still offering the adjustments that experienced welders appreciate for customizing their welds.

The SVM154-A also includes several safety features, such as thermal overload protection and a dynamic power control, ensuring safe operation while maintaining high productivity. Users benefit from features that protect both the machine and the operator, making it a reliable choice for long hours of work.

Moreover, Lincoln Electric's commitment to durability is evident in the SVM154-A's construction. Built with high-quality materials, this welding machine is designed to withstand the rigors of daily use, ensuring longevity and reliability over time.

In summary, the Lincoln Electric SVM154-A stands out for its portability, versatility, and user-centric design. With advanced inverter technology that promotes energy efficiency and a stability for various welding processes, it serves as a valuable tool for both professionals and hobbyists seeking to achieve high-quality welds across different applications. Its combination of advanced features, safety mechanisms, and rugged durability positions the SVM154-A as a top choice in the welding equipment market.