Lincoln Electric SVM154-A 34TROUBLESHOOTING and REPAIRF-34, GAS Solenoid Removal and Replacement

Page 79

Section TOC

Master TOC

F-34TROUBLESHOOTING AND REPAIRF-34

GAS SOLENOID REMOVAL AND REPLACEMENT (continued)

FIGURE F.7 — GAS SOLENOID REMOVAL AND REPLACEMENT.

Return to

Return to

CLAMP

LINCOLN

ELECTRIC

SOLENOID

MOUNT

Return to Section TOC

Return to Master TOC

GAS

HOSE

NOTE: WIRE FEEDER SHOWN WITH DRIVE MOTOR ASSEMBLY REMOVED FOR CLARITY

PROCEDURE

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

1.Remove input power to the LN-10 unit.

2.Using the 5/16 in. nut driver, remove the wire drive cover.

3.Locate the gas solenoid assembly and remove the input gas lines using pliers. See Figure F.7.

4.Label and remove the two leads con- nected to the solenoid.

5.Remove the rubber hose and clamp from the gas solenoid. Be careful not to damage the rubber hose.

6.Using the 5/16 in. wrench remove the two screws that mount the solenoid assembly to the rear panel of the wire feeder.

7.Remove the solenoid assembly from the LN-10 unit.

8.Using the Phillips head screwdriver remove the two screws holding the solenoid to the bracket. Remove the solenoid.

9.Mount the new solenoid onto the bracket using the two Phillips head screws.

10.Install the solenoid assembly into the LN-10.

11.Connect the gas hose.

12.Connect the two wires previously removed. Be sure the leads are connected to their original positions.

13.Install the wire drive cover and connect the input gas line.

LN-10

Page 78 Page 80
Image 79
Page 78 Page 80
Contents SVM154-A ISAFETYi Fumes and Gases SafetyIii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéMaster Table of Contents for ALL Sections Table of Contents Installation Section InstallationGeneral Description Technical Specifications LN-10 Head & ControlRecommended Processes and Equipment Safety PrecautionsInstallation of the LN-10 Boom Mount Wire Feeder Components Mounting the 10 Series Wire DriveConnecting Wire Drive Unit to Control Box Mounting Synergic 7F Wire Drive Unit K679-1 orMounting the LN-10 Control Box Electrode Routing Wire Drive Speed Range SelectionControl Speed Range Setting Series Wire Drive Ratio SelectionSynergic 7F Wire Drive 4-Roll Kits KP655 and KP656 Wire Feed Drive Roll KitsProcedure to Install Drive Roll and Wire Guides Series Wire Drive Roll Kit Installation KP1505 and KP1507Innershield Guns GUN and Cable Assemblies with Standard ConnectionGUN and Cable Assemblies with FAST-MATE Connection Gmaw GunsBuildup of Shielding GAS may harm health or kill 8INSTALLATIONA-8Series Wire Drive Water Connections for Water Cooled Guns Cylinder may explode if damagedInput Cable LN-10 Control to Power Source Electrical InstallationMaterials Required for boom to bench conversion Optional Features InstallationBoom and Bench Conversions Materials Required for bench to boom conversionOperation Table of Contents Operation SectionSetup DIP Switch Access LN-10 Control DIP Switch SetupSetting the DIP Switches Wire Drive Head SelectionWelding Power Source Selection S2 switch 1 on = m/min Step Trigger Mode Operation SelectionSecurity Mode Selection Metric/English Wire Feed Speed Display SelectionS2 switch 4 OFF = Robotics mode OFF As shipped Maximum Limits Setting Mode SelectionS2 switch 4 on = Robotics mode on S2 switch 6 on Minimum Limits Setting mode onKeypad and Display Description Power-Down SaveProcedure Lights Indicate which Keypad and Display OperationTrigger Mode Selection Display Control Keys Digital Memory Voltmeter Control Control Select key enables operator toMaximum and Minimum Limits Setting Modes Wire Reel Loading READI-REELS Spools or Coils Dual Procedure RemoteFigure B.2 GAS Guard Regulator Setting Procedure for Setting Angle of FeedplateMaking a Weld DH-10 Wire Reel ChangingWire Feed Overload Protection Grounding Lead ProtectorDisplay Prompt or Error Explanation of Prompting Error MessagesTable of Contents Accessories Section AccessoriesGeneral Table C.1 LN-10 Wire Feeder AccessoriesAluminum Electrode For use with Binzel Guns Only Wire Size Solid Steel ElectrodeCored Electrode Aluminum ElectrodeInput Cable Assemblies K683-1 Dual Procedure SwitchK683-3 Dual Procedure Switch K1449-1 Dual ProcedureK1561-1 Robotics Interface Module K1558-1 Remote Switch Interface ModuleGUN Adapters for 10 Series GUN and Cable AssembliesK1556-1 Light Duty Caster KIT K1557-1 Swivel MountK1555-1 Insulated Lift Hook Table of Contents Maintenance Section MaintenancePeriodic Maintenance MaintenanceAvoiding Wire Feeding Problems Safety Precautions Routine MaintenanceFigure D.1 Major Component Locations Theory of Operation Table of Contents Theory of Operation SectionControl Board Input RECEPTACLE, Control Board and Operator Controls Figure E.3 LN-10 Wire Feed Head and Receptacle Wire Feed Head ReceptacleTheory of Operation Protection and Shutdown Wire Feed Overload Loss of Voltage Sense Protection ShutdownLN-10 Table of Contents Troubleshooting and Repair Section Troubleshooting and RepairReturn to Return to Master TOC HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures LN-10 Function Problems Troubleshooting GuideFunction Problems Power Source Selection Function Problems Mode Selection Perform the Encoder Board Test Troubleshooting and Repair Mum and minimum limit set Perform the Gas Solenoid Test Feeding Problems Welding Problems LN-10 Materials Needed Test ProceduresWire Drive Motor Test Test DescriptionTest Procedure Wire Drive Motor TestMaterials Needed Tach Adjustment and Feedback TestTach Adjustment and Feedback Test 20TROUBLESHOOTING and REPAIRF-20Tach Adjustment Procedure LN-10 Keypad Resistance Test Keypad Resistance Test 24TROUBLESHOOTING and REPAIRF-24Control Ohms 50 Ohms Typical LN-10 Encoder PC Board Test Figure F.4 Encoder PC Board Test Encoder PC Board TestGAS Solenoid Test GAS Solenoid Test 30TROUBLESHOOTING and REPAIRF-30Display PC Board Removal and Replacement Component Replacement ProceduresReplacement Procedure 32TROUBLESHOOTING and REPAIRF-32Display PC Board Removal and Replacement Removal ProcedureGAS Solenoid Removal and Replacement GAS Solenoid Removal and Replacement 34TROUBLESHOOTING and REPAIRF-34Encoder PC Board Removal and Replacement Figure F.8 Encoder PC Board Removal and Replacement Encoder PC Board Removal and ReplacementWire Drive Motor and Gear BOX Removal and Replacement Figure F.9 Wire Feed Assembly Removal Wire Drive Motor and Gear BOX Removal and ReplacementTo Remove the Drive Motor from the Gear BOX To Remove the Wire Drive Assembly from the Gear BOXReplacement Procedures Current Sensing Reed Switch Removal and Replacement Current Sensing Reed Switch Plug Retest After Repair Check Wire Feed Speed RangeElectrical Diagrams Section Wiring Diagram LN-10 Control Electrical DiagramsElectrode Cable From Current Sensor Wiring Diagram LN-10 Wire DriveSchematic Control PC Board #1 Circuitry Tach Schematic Control PC Board #23168 G PC Board ASSEMBLY-CONTROL5VA Schematic Display PC BoardBoard 22066 Schematic Encoder PC BoardEncoder PC Board ASSEMBLY-ENCODERSVM Error Reporting Form

SVM154-A specifications

The Lincoln Electric SVM154-A is a powerful and versatile inverter-based welding machine designed for a wide range of applications. As a part of Lincoln Electric's esteemed portfolio, this model is particularly favored for its robust performance and cutting-edge technologies, making it ideal for both professional fabricators and hobbyists alike.

One of the standout features of the SVM154-A is its compact and lightweight design, which enhances portability without compromising power. Weighing significantly less than traditional welding machines, it allows welders to easily transport the equipment to various job sites. This feature is particularly beneficial in industries where mobility is essential.

Equipped with advanced inverter technology, the SVM154-A delivers a stable and smooth arc, providing consistent welding performance even in challenging conditions. The inverter design also contributes to energy efficiency, allowing users to save on operational costs while enjoying superior performance. The machine supports both MIG and TIG welding processes, which adds to its versatility. This adaptability makes it suitable for a range of materials including mild steel, stainless steel, and aluminum.

Another notable characteristic is its user-friendly interface. Designed with the welder in mind, the SVM154-A includes intuitive controls that simplify settings adjustments and operational processes. This ergonomic layout allows for ease of use, even for beginners, while still offering the adjustments that experienced welders appreciate for customizing their welds.

The SVM154-A also includes several safety features, such as thermal overload protection and a dynamic power control, ensuring safe operation while maintaining high productivity. Users benefit from features that protect both the machine and the operator, making it a reliable choice for long hours of work.

Moreover, Lincoln Electric's commitment to durability is evident in the SVM154-A's construction. Built with high-quality materials, this welding machine is designed to withstand the rigors of daily use, ensuring longevity and reliability over time.

In summary, the Lincoln Electric SVM154-A stands out for its portability, versatility, and user-centric design. With advanced inverter technology that promotes energy efficiency and a stability for various welding processes, it serves as a valuable tool for both professionals and hobbyists seeking to achieve high-quality welds across different applications. Its combination of advanced features, safety mechanisms, and rugged durability positions the SVM154-A as a top choice in the welding equipment market.
Top Page Image Contents