Lincoln Electric PRO 100 manual Welding In The Vertical Position, Penetration, Fillet Welds

Page 23

B-10

LEARNING TO WELD

B-10

 

 

 

FIGURE B.12

Penetration

Unless a weld penetrates close to 100% of the metal thickness, a butt weld will be weaker than the material welded together. In the example shown in Figure B.13, the total weld is only half the thickness of the material thus the weld is only approximately half as strong as the metal.

45°

FIGURE B.15

Welding In The Vertical Position

Welding in the vertical position can be done either ver- tical-up or vertical-down. Vertical-up is used whenever

alarger, stronger weld is desired. Vertical-down is used primarily on sheet metal 5/32” (3.9 mm) and under for fast, low penetrating welds.

FIGURE B.13

FIGURE B.14

In the example shown in Figure B.14, the joint has been welded so that 100% penetration could be achieved. The weld, if properly made, is as strong as or stronger than the original metal.

Fillet Welds

When welding fillet welds, it is very important to hold the wire electrode at a 45° angle between the two sides or the metal will not distribute itself evenly. The gun nozzle is generally formed at an angle to facilitate this. See Figure B.15.

WARNING

Use of this unit on thicker materials than recom- mended may result in poor welds. The welds may “look” good, but may just be “sitting” on top, of the plate. This is called “Cold Casting” and will result in weld failure.

Vertical-up And Overhead Welding

The problem, when welding vertical-up, is to put the molten metal where it is wanted and make it stay there. If too much molten metal is deposited, gravity will pull it downwards and make it “drip”. Therefore, a certain technique has to be followed.

When welding out-of-position, run stringer beads. Don’t whip, break the arc, move out of the puddle, or move too fast in any direction. Use Wire Feed Speed (WFS) in the low portion of the range. The general technique and proper gun angle is illustrated in Figure B.16.

Generally, keep the electrode nearly perpendicular to the joint as illustrated. The maximum angle above per- pendicular may be required if porosity becomes a problem.

PRO 100

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PRO California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéPlease Examine Carton and Equipment For Damage Immediately Thank YouTable of Contents Technical Specifications PRO InstallationIdentify and Locate Components Safety PrecautionsRead entire installation section before starting InstallationStacking Work Clamp InstallationSelect Suitable Location Output ConnectionsGAS Connection Optional GUN InstallationWork Cable Installation Connecting Gun Cable to the PROFigure A.5 Requirements For CSA Rated Output Input ConnectionsRequirements For Rated Output Code Requirements for Input ConnectionsWelding Sparks can cause fire or explosion Observe all safety information throughout this manual1OPERATIONB-1 Fumes and Gases can be dangerousOperation Sequence of Operation Wire LoadingWelding Operations Wire Threading Friction Brake AdjustmentsMaking a Weld Cleaning Tip And NozzleProcess Guidelines Overload Protection Changing Machine Over to Feed Other Wire SizesWelding with Gmaw MIG SELF-SHIELDED Fcaw Welding ARC Learning to WeldLearning to Weld ARC-WELDING CircuitFor Gmaw MIG Process Gmaw MIG Welding ARCProcess Selection Butt Welds Common MetalsJoint Types and Positions For Fcaw Innershield ProcessFillet Welds Welding In The Vertical PositionPenetration Correct Welding Position Machine SET UP for the SELF-SHIELDED Fcaw ProcessWelding Techniques for the SELF- Shielded Fcaw Process Vertical-down WeldingCorrect Welding Speed Correct Electrical Stickout ESOPractice Helpful HintsWelding Techniques for the Gmaw MIG Process Machine SET UP for the Gmaw MIG ProcessFor the PRO 100, use the following To Eliminate Stubbing* in order of importance Troubleshooting WeldsTo Eliminate a Ropy Convex Bead in order of importance To Correct Poor Penetration in order of impor- tanceProper Gun Handling Application Chart K610-1 MIG Conversion Kit for the PRO AccessoriesOptional Accessories MIG ConversionRoutine Maintenance MaintenanceMaintenance Safety Precautions Contact Tip Cable Liner Drive Roll GUN and Cable MaintenanceConfiguration of Components in Wire Feeding System For Magnum 100L GUNChanging Drive Roll Component Replacement ProceduresChanging the Contact TIP Liner trim length Changing LinerFigure D.3 GUN Handle PartsHOW to USE Troubleshooting Guide 1TROUBLESHOOTINGE-1Recommended Course of Action TroubleshootingTroubleshooting Guide Problems Possible Areas Symptoms MisadjustmentsFeeding Problems Welding Problems PRO100 Wiring Diagram DiagramsPRO $700.00 How To Read Shop DrawingsNew Lessons in Arc Welding Need Welding Training?Precaucion Warnung

PRO 100 specifications

The Lincoln Electric PRO 100 is a compact and versatile multi-process welder designed to meet the needs of both novice and experienced welders. Known for its robust build quality and advanced features, the PRO 100 is engineered for tasks ranging from light fabrication to heavy-duty welding projects.

One of the standout features of the PRO 100 is its multi-process capability. It can seamlessly switch between MIG, Stick, and TIG welding, allowing users to tackle various materials including aluminum, stainless steel, and mild steel with ease. This versatility makes it an essential tool for welding professionals and hobbyists alike, enhancing productivity and efficiency on the job.

The machine is equipped with Lincoln Electric's unique Auto-Set technology, which simplifies the setup process for users. By automatically adjusting the voltage and wire feed speed based on the selected material and thickness, it enables welders to achieve optimal results without extensive experience or technical knowledge. This feature not only saves time but also reduces the likelihood of mistakes, making it ideal for beginners.

Powering the PRO 100 is a reliable inverter-based technology that ensures smooth and consistent arcs. This technology not only enhances performance but also improves energy efficiency, making the machine more cost-effective in the long run. The compact design allows for portability, making it convenient for job sites where space may be limited.

The PRO 100 also boasts several safety features that protect both the user and the machine. It includes an overload protection system that prevents overheating, ensuring the longevity of the welder. Additionally, the welder features a rugged construction that can withstand demanding work environments, further enhancing its durability.

Furthermore, the PRO 100 is designed for user comfort and control. The intuitive interface and large color display provide clear readability of settings and parameters, allowing for quick adjustments. The adjustable wire feed speed and voltage settings give welders the flexibility to customize their welding experience.

In summary, the Lincoln Electric PRO 100 stands out in the crowd of welding machines for its multi-process capabilities, Auto-Set technology, and inverter-based power system. Its combination of portability, durability, and user-friendly features makes it an excellent choice for a wide range of welding applications, whether at home, in the workshop, or on the field. This well-rounded welder can help elevate the quality of the work for both the novice and the seasoned professional.
Top Page Image Contents