Lincoln Electric manual For the PRO 100, use the following

Page 28

B-15

LEARNING TO WELD

B-15

 

 

 

Contact Tip

Wire Electrode

ESO

FIGURE B.24

3.The Correct Electrical Stickout (ESO)

The electrical stickout (ESO) is the distance from the end of the contact tip to the end of the wire. See Figure B.24.

Once the arc has been established, maintaining the correct ESO becomes extremely important. The ESO should be approximately 3/8 to 1/2 inch (10 to 12 mm) long.

The easiest way to tell whether the ESO is the cor- rect length is by listening to its sound. The correct ESO has a distinctive “crackling” sound, very much like eggs frying in a pan. A long ESO has a hollow, blowing or hissing sound. If the ESO is too short, you may stick the contact tip or nozzle to the weld puddle and/or fuse the wire to the contact tip.

4.The Correct Welding Speed

The important thing to watch while welding is the puddle of molten metal right behind the arc. See Figure B.25. Do not watch the arc itself. It is the appearance of the puddle and the ridge where the molten Puddle solidifies that indicates correct weld- ing speed. The ridge should be approximately 3/8” (10 mm) behind the wire electrode.

Most beginners tend to weld too fast, resulting in a thin, uneven, “wormy” looking bead. They are not watching the molten metal.

Molten puddle

Weld metal ridge

Base metal

FIGURE B.25

Helpful Hints

1.For general welding, it is not necessary to weave the arc, neither forward or backward nor sideways. Weld along at a steady pace. You will find it easier.

2.When welding on thin plate, you will find that you will have to increase the welding speed, whereas when welding on heavy plate, it is necessary to go more slowly in order to get good penetration.

3.When welding sheet metal 16 gauge (1.5 mm) and lighter, heat buildup may cause part warpage and burn through. One way to eliminate these problems is to use the back-stepping method illustrated in Figure B.21.

Practice

The best way of getting practice in the four skills that enable you to maintain:

1.Correct welding position

2.Correct way to strike an arc

3.Correct electrical stickout

4.Correct welding speed

is to perform the following exercise.

For the PRO 100, use the following:

Mild Steel

16 gauge or 1/16 inch

 

(1.6 mm)

Electrode

Lincolnweld 0.025 L-56

 

electrode

 

CO2

Voltage Setting “V”

C

Wire Feed Speed “oo”

4

 

 

Refer to Figure B.22.

 

1.Learn to strike an arc by positioning the gun over the joint and touching the wire to the work.

2.Position face shield to protect face and eyes.

3.Depress gun trigger, hold gun so contact tip to work distance Is about 3/8 to 1/2 inch (10 to 12 mm) and the gun is at proper angle.

PRO 100

Page 27 Page 29
Image 28
Page 27 Page 29
Contents PRO Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Installation Technical Specifications PROSafety Precautions Read entire installation section before startingInstallation Identify and Locate ComponentsWork Clamp Installation Select Suitable LocationOutput Connections StackingGUN Installation Work Cable InstallationConnecting Gun Cable to the PRO GAS Connection OptionalFigure A.5 Input Connections Requirements For Rated OutputCode Requirements for Input Connections Requirements For CSA Rated OutputObserve all safety information throughout this manual 1OPERATIONB-1Fumes and Gases can be dangerous Welding Sparks can cause fire or explosionOperation Welding Operations Wire LoadingSequence of Operation Friction Brake Adjustments Wire ThreadingProcess Guidelines Cleaning Tip And NozzleMaking a Weld Welding with Gmaw MIG Changing Machine Over to Feed Other Wire SizesOverload Protection Learning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARCProcess Selection Gmaw MIG Welding ARCFor Gmaw MIG Process Common Metals Joint Types and PositionsFor Fcaw Innershield Process Butt WeldsPenetration Welding In The Vertical PositionFillet Welds Machine SET UP for the SELF-SHIELDED Fcaw Process Welding Techniques for the SELF- Shielded Fcaw ProcessVertical-down Welding Correct Welding PositionCorrect Electrical Stickout ESO Correct Welding SpeedHelpful Hints PracticeMachine SET UP for the Gmaw MIG Process Welding Techniques for the Gmaw MIG ProcessFor the PRO 100, use the following Troubleshooting Welds To Eliminate a Ropy Convex Bead in order of importanceTo Correct Poor Penetration in order of impor- tance To Eliminate Stubbing* in order of importanceProper Gun Handling Application Chart Accessories Optional AccessoriesMIG Conversion K610-1 MIG Conversion Kit for the PROMaintenance Safety Precautions MaintenanceRoutine Maintenance GUN and Cable Maintenance Configuration of Components in Wire Feeding SystemFor Magnum 100L GUN Contact Tip Cable Liner Drive RollChanging the Contact TIP Component Replacement ProceduresChanging Drive Roll Changing Liner Liner trim lengthGUN Handle Parts Figure D.31TROUBLESHOOTINGE-1 HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting GuideProblems Possible Areas Symptoms Misadjustments Recommended Course of ActionFeeding Problems Welding Problems Diagrams PRO100 Wiring DiagramPRO How To Read Shop Drawings New Lessons in Arc WeldingNeed Welding Training? $700.00Precaucion Warnung

PRO 100 specifications

The Lincoln Electric PRO 100 is a compact and versatile multi-process welder designed to meet the needs of both novice and experienced welders. Known for its robust build quality and advanced features, the PRO 100 is engineered for tasks ranging from light fabrication to heavy-duty welding projects.

One of the standout features of the PRO 100 is its multi-process capability. It can seamlessly switch between MIG, Stick, and TIG welding, allowing users to tackle various materials including aluminum, stainless steel, and mild steel with ease. This versatility makes it an essential tool for welding professionals and hobbyists alike, enhancing productivity and efficiency on the job.

The machine is equipped with Lincoln Electric's unique Auto-Set technology, which simplifies the setup process for users. By automatically adjusting the voltage and wire feed speed based on the selected material and thickness, it enables welders to achieve optimal results without extensive experience or technical knowledge. This feature not only saves time but also reduces the likelihood of mistakes, making it ideal for beginners.

Powering the PRO 100 is a reliable inverter-based technology that ensures smooth and consistent arcs. This technology not only enhances performance but also improves energy efficiency, making the machine more cost-effective in the long run. The compact design allows for portability, making it convenient for job sites where space may be limited.

The PRO 100 also boasts several safety features that protect both the user and the machine. It includes an overload protection system that prevents overheating, ensuring the longevity of the welder. Additionally, the welder features a rugged construction that can withstand demanding work environments, further enhancing its durability.

Furthermore, the PRO 100 is designed for user comfort and control. The intuitive interface and large color display provide clear readability of settings and parameters, allowing for quick adjustments. The adjustable wire feed speed and voltage settings give welders the flexibility to customize their welding experience.

In summary, the Lincoln Electric PRO 100 stands out in the crowd of welding machines for its multi-process capabilities, Auto-Set technology, and inverter-based power system. Its combination of portability, durability, and user-friendly features makes it an excellent choice for a wide range of welding applications, whether at home, in the workshop, or on the field. This well-rounded welder can help elevate the quality of the work for both the novice and the seasoned professional.
Top Page Image Contents