Lincoln Electric IM702-A manual Auxiliary Power Connections, Figure A.3

Page 14

A-7

INSTALLATION

A-7

 

 

 

FIGURE A.3

AUXILIARY POWER CONNECTIONS

The Precision TIG machines provide a standard NEMA 5-15R duplex receptacle, located on the upper case back on the torch side of the machine:

•The bottom outlet of this duplex receptacle provides switched 115VAC power for the Under-Cooler, or Water Solenoid accessory. This Cooler receptacle turns on when the arc starts and remains on for about 8 minutes after the arc goes out (with the Fan-As- Needed machine cooling fan, see Maintenance Section), so the Cooler’s fan and water pump will not run continuously in idle, but will run while welding.

•The top outlet of this duplex receptacle provides at least 8 amps at 115VAC, whenever the Precision TIG Power switch is ON. This auxiliary circuit is intended for running 115VAC accessories or small power tools. Note: Some types of equipment, especially pumps and large motors, have starting currents which are significantly higher than their running current. These higher starting currents may cause the circuit breaker to open. (See next paragraph)

•Both the receptacle circuits are protected from shorts and overloads by a 15 amp circuit breaker, located above the receptacle. if the breaker trips its button pops out exposing a red ring. When the circuit break- er cools the button can be reset by pressing it back in.

Note: When the breaker trips not only will the auxil- iary and cooler power be interrupted, but so will the power to the shielding gas solenoid and machine cooling fan.

For Gas Supply hose with 5/8-18RH male (Provided with Weld Package model)

For Coolant Supply Hoses

with 5/8-18LH male (Provided with Weld Package model

or Under-Cooler Cart)

The Precision TIG Export models also provide a grounded 220vac Euro type Schuko receptacle and a 5 amp circuit breaker, located on the upper case back on the reconnect side of the machine, intended for use with a 220vac water cooler.

REMOTE CONTROL (If Used)

The Foot Amptrol (included with the Precision TIG Welding Package), or other Remote accessory, is installed by routing the plug of its control cable up through the left cable strain relief hole provided in the base (see Figure A.2), then connecting the 6-pin plug to the mating Remote receptacle behind the stud panel cover. (See Operation Section B-2 for mating plug wiring.)

Note: If the Precision TIG is equipped with an Under- Cooler or Under-Storage unit, the Foot Pedal (or other remote control accessory) and coiled control cable, or excess cable length, may be conveniently stored in the drawer while remaining connected.

PRECISION TIG 275

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Precision TIG Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Precision TIG InstallationRated Input Single Phase only Temperature Ranges Recommended Input Wire and Fuse SizesPhysical Dimensions Additional Output CapacitySafety Precautions Input and Grounding Connections Output CABLES, Connections and Limitations Work Cable ConnectionStick Electrode Cable Connection TIG Torch Connection Figure A.2Auxiliary Power Connections Figure A.3Robotic Interface Connection Figure A.4Pipe Thawing OperationProduct Description Welding SparksProcess Limitations Recommended Processes and EquipmentRecommended Processes Equipment LimitationsControls and Settings Figure B.1 Control PanelOperation Do not USE 4-STEP if Using AN Amptrol Remote Advanced Panel ControlsOperation TIG Welding Features Internal SET UP ControlsStick Welding Features Figure B.3 Figure B.4 Using the Start Pedal Foot Amptrol K870-1 TIG Weld Cycle ChartSetup Guidelines for TIG Welding with AN Amptrol Figure B.5 Making a TIG Weld with AN Amptrol Recommended Electrode Amperage Ranges Precision TIGField Installed Options AccessoriesFactory Installed Options Optional EquipmentRoutine and Periodic Maintenance MaintenanceSafety Precautions Overload ProtectionSpark GAP Adjustment Service ProceduresComponent Access UNDER-COOLER ServiceTroubleshooting HOW to USE Troubleshooting GuideCourse of Action SymptomsOutput Problems Meter Problems GAS ProblemsHI-FREQ Problems Preset & Output Control Problems Stick Welding Problems TIG Welding ProblemsTIG Problems Precision TIG 275 Wiring Diagram for Code SCR3 Enhanced Diagrams Dimension Print K1826-1 DOMESTIC, K1826-2 Canada and K1827-1 Export Precision TIG Warnung Aviso DE

IM702-A specifications

The Lincoln Electric IM702-A is a versatile and innovative welding machine that has garnered attention for its advanced features and robust performance. Designed for various welding applications, the IM702-A is a go-to choice for professionals in the industry, offering precision, reliability, and ease of use.

One of the standout characteristics of the IM702-A is its advanced inverter technology. This allows for a lightweight and compact design, making it easier to maneuver in tight spaces compared to traditional welding machines. The inverter technology also contributes to energy efficiency, reducing power consumption without compromising on performance.

The IM702-A features a multi-process capability, enabling it to perform MIG, TIG, and Stick welding with ease. This versatility makes it ideal for a wide range of projects, from industrial manufacturing to home repairs. Users can seamlessly switch between different welding processes, enhancing productivity and streamlining workflow.

In terms of user interface, the Lincoln Electric IM702-A is designed with convenience in mind. It boasts a digital display that provides real-time information on welding parameters, making it easier for operators to monitor and adjust settings as needed. The intuitive controls are user-friendly, allowing even novice welders to achieve professional-quality results.

The machine also includes advanced weld control features, such as precise amperage and voltage adjustments. These controls ensure that users can achieve optimal settings for different materials and thicknesses, resulting in clean, strong welds. Additionally, the IM702-A is equipped with an automatic voltage adjustment feature, which helps maintain consistent performance under varying input conditions.

Durability is another key selling point for the IM702-A. Built with high-quality materials and engineering, this welding machine is designed to withstand the rigors of daily use in demanding environments. Its rugged construction provides reliability and longevity, ensuring that it remains a valuable asset in any workshop.

Lastly, safety is a priority in the design of the IM702-A. It includes several built-in safety features, such as thermal overload protection and a stabilized arc performance that reduces the risk of arc blow, protecting both the operator and the equipment.

Overall, the Lincoln Electric IM702-A stands out in the welding market due to its advanced technologies, multi-process capabilities, user-friendly interface, and robust safety features, making it an excellent choice for professional welders seeking high-quality performance and versatility.
Top Page Image Contents