Milwaukee 6460, 6375-20, 6376-20, 6405-6 manual General Operation Fig

Page 8

OPERATION

WARNING!

To reduce the risk of injury, wear safety goggles or glasses with side shields. Unplug the tool be- fore changing accessories or making adjust- ments .

8.Set the depth of cut for no more than 1/8" to 1/4" greater than the thickness of the stock. The less blade exposed, the less chance of binding and KICKBACK. Before cutting, be sure depth and bevel adjustments are tight.

9.Be cautious of pitchy, knotty, wet or warped stock. These are most likely to create pinching conditions and possible KICKBACK. Do not rip warped lumber. Avoid cutting nails.

Causes and Operator Prevention of KICKBACK:

KICKBACK is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator.

When the blade is pinched or bound tightly by the kerf, or cutting slot, closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward operator.

KICKBACK is the result of tool misuse and/or incorrect operating pro- cedures or conditions and can be avoided by taking proper precautions as given below:

1.Maintain a firm grip with both hands on the saw and posi- tion your body and arm to allow you to resist KICKBACK forces. KICKBACK forces can be controlled by the operator, if proper precautions are taken.

2.When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

3.When restarting a saw in the workpiece, center the saw blade in the kerf, or cut, and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.

4.Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

5.Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK.

6.Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.

7.Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK.

10.Use a rip fence or edge guide when ripping. Guides improve control and reduce blade binding.

11.Stay alert. Any distraction can cause twisting or binding. Repetitive cuts may lull the user into careless movements.

General Operation (Fig. 8)

Always clamp the workpiece securely on a saw horse or bench. See “Applications” for the correct way to support your work in different situations.

1.Draw a cutting line. Place the front of the shoe on the edge of the workpiece without making blade contact. Hold the switch handle with one hand and the depth/bevel adjusting knob (depending on model) with the other (Fig. 8). When using 10-1/4" saws, hold the switch handle with one hand and the front handle with the other.

Fig. 8

2.Line up the line sight with your cutting line. Position your arms and body to resist KICKBACK. Pull the trigger, allowing the motor to reach full speed before beginning to cut.

3.While cutting, keep the shoe flat against the workpiece and maintain a firm grip. Do not force the saw through the work. Forcing a saw can cause KICKBACK.

4.If making a partial cut, restarting in mid-cut or correcting direction, allow the blade to come to a complete stop. To resume cutting, center the blade in the kerf, back the saw away from cutting edge a few inches, pull the trigger and re-enter the cut slowly.

5.If the saw binds and stalls, maintain a firm grip and release the trigger immediately.

6.After finishing a cut, be sure the lower guard closes and the blade comes to a complete stop before setting the saw down.

page 8

Image 8
Contents Operators Manual Work Area Safety Power Tool USE and Care Electrical SafetyPersonal Safety ServiceSpecific Safety Rules Circular Saws Causes and Operator Prevention of KickbackFunctional Description Guidelines for Using Extension Cords Recommended Minimum Wire Gauge For Extension CordsGrounding Extension CordsTool Assembly Installing and Removing Blades on 7-1/4 & 8-1/4 SawsInstalling and Removing Blades on 10-1/4 Saws Adjusting Depth 7-1/4 SawsAdjusting Bevel Angle 8-1/4 and 10-1/4 Saws Bevel Adjustment Screw 7-1/4, 8-1/4, 10-1/4 Saws FigAdjusting Bevel Angle 7-1/4 Saws Adjusting Depth 8-1/4 and 10-1/4 SawsOperation General Operation FigTroubleshooting ApplicationsElectric Brake Select Models Ripping WoodPocket Cutting Fig Cutting Masonry and MetalMaintenance AccessoriesFive Year Tool Limited Warranty CleaningConserver CES Instructions Sécurité DU Lieu DE Travail Sécurité ÉlectriqueSécurité Individuelle Utilisation ET Entretien DE L’OUTIL ÉlectriqueRègles DE Sécurité Particulière Scies Circulaire Causes du retour d’outil et prévention par l’utilisateurDe Coupe à Description FonctionnelleNo de Volts Min Calibre Arbre Profondeur Cat Vide De Lame Calibres minimaux recommandés pour Les cordons de rallonge Mise À LA Terre AvertissementCordons DE Rallonge Trois dentsMontage DE Loutil Avertissement Réglage de profondeur scies circulaire 184 mm 7-1/4 et M 1/4Maniement Avertissement Dépistage des dérangements Règles générales d’opération FigFrein életronique modèles spécifiques Applications Avertissement Maintenance Avertissement Accessoires AvertissementGarantie Limitée DE L’OUTIL DE Cinq ANS NettoyageGUA0RDE Estas Instrucciones Seguridad EN EL Área DE Trabajo Seguridad EléctricaSeguridad Personal USO Y Cuidado DE LAS Herramientas EléctricasReglas Especificas DE Seguridad Sierras Circulares Descripciónfuncional Cat VoltsGuías para el uso de cables de extensión Tierra ¡ADVERTENCIAExtensiónes Eléctricas Ensambaje DE LA Herramienta ¡ADVERTENCIA Ajuste de profundidad sierras de 184 mm 7-1/4 yCómo ajustar el ángulo del bisel sierras 184 mm 7-1/4 y Operacion ¡ADVERTENCIA Freno eléctrico modelos especificas Solución de problemasOperación en general Fig Applicaciones ¡ADVERTENCIA Cortando a lo largoCortando madera a través Fig CortCorte de concreto y metalMantenimiento ¡ADVERTENCIA Accesorios ¡ADVERTENCIAGarantía Limitada DE Cinco Años LimpiezaSawdust

6405-6, 6376-20, 6375-20, 6460 specifications

Milwaukee has long been a trusted name in power tools, and its line of cordless tools continues to push the boundaries of performance and efficiency. Among their impressive catalog, models Milwaukee 6460, 6375-20, 6376-20, and 6405-6 stand out as prime examples of cutting-edge technology and user-centric design.

The Milwaukee 6460, also known as the M18 FUEL 1/2” Hammer Drill/Driver, is a powerhouse designed for professional contractors. It boasts a brushless motor that delivers up to 1,200 in-lbs of torque, making it perfect for heavy-duty applications. One of its main features is the REDLINK PLUS intelligence, which provides advanced overload protection and ensures optimal performance under load. With a compact design, it enhances maneuverability in tight spaces, an essential trait for any job site.

Next is the Milwaukee 6375-20, a 7-1/4” circular saw that enables users to achieve straight, accurate cuts in a range of materials. It features a powerful 15-amp motor that produces up to 5,800 RPM, allowing for fast and efficient cutting. The saw’s magnesium construction contributes to its lightweight yet durable design, reducing user fatigue while ensuring longevity. Additionally, the electric brake enhances safety by stopping the blade quickly after release of the trigger.

The Milwaukee 6376-20 is known for its versatility as a 7-1/4” rear handle circular saw. This model offers a similar powerful motor but is engineered for different cutting orientations. Its ergonomic design, along with an integrated rafter hook, makes it ideal for use in framing and roofing applications. Furthermore, the LED light ensures visibility in poorly lit conditions, enabling precise cuts no matter where the job takes you.

Lastly, the Milwaukee 6405-6 band saw is engineered for efficient cutting of metal and other materials, featuring a variable speed control that allows users to adjust the saw speed between 0-200 FPM depending on the material being cut. Its lightweight design and carrying handle make it easily portable, making it a go-to tool for contractors who need to cut on the go. The integrated LED work light adds another layer of convenience, ensuring proper visibility during operations.

In summary, Milwaukee 6460, 6375-20, 6376-20, and 6405-6 embody the brand’s commitment to producing high-quality, high-performance tools that meet the demands of professionals. Their innovative technologies and thoughtful designs enhance user experience while ensuring durability and efficiency on the job site. Whether you are drilling, cutting, or slicing through materials, Milwaukee offers tools that deliver unmatched reliability.