Milwaukee 6180-20 Operation, Using the Fixtec Nut, Removing and Installing Cut-Off Wheels Fig

Page 6

OPERATION

WARNING!

To reduce the risk of injury, always unplug tool before attaching or removing accessories. Use only specifically recommended accessories. Others may be hazardous.

Using the Transport Lock

The transport lock secures the handle for transporting and storing the tool. To release the transport lock, push down the handle and pull out the transport lock. To lock the transport lock, push down the handle and push in the transport lock.

WARNING!

To reduce the risk of injury, do not use the FIXTEC nut on any other tool. The FIXTEC nut is specifically designed for this application and may be hazardous when used on other tools.

Using the FIXTEC Nut

The FIXTEC nut allows for wheel changes without tools. To use the FIXTEC nut, pull out the hinged latch and spin off the nut. To replace the nut, hand tighten the nut until it is secure. Do not over tighten the nut. This may damage the wheel and the flanges. When the nut is tight, snap the hinged latch back into position. Make sure the hinged latch is down before using the tool.

WARNING!

To reduce the risk of injury, use only the proper TYPE 1 wheels made for this machine. DO NOT USE TOOTHED BLADES.

Removing and Installing Cut-Off Wheels (Fig. 1)

The cut-off machine is supplied with the abrasive cut-off wheel installed. MILWAUKEE recommends using only MILWAUKEE 14" Abrasive Cut-Off Wheels, 3/32" wide with this tool. Before operating the tool, make sure the wheel is in good condition as described in the “Specific Safety Instructions - Abrasive Cut-Off Machines”.

Fig. 1

Moveable portion of guard

 

Inner flange

Abrasive cut-off

wheel

Outer flange

FIXTEC nut

To change wheels:

1.Unplug tool.

2.Release the transport lock.

3.Pull back the moveable portion of the guard to expose the wheel arbor and FIXTEC nut.

Press down the spindle lock lever and loosen the FIXTEC nut (counterclockwise).

4.Remove the FIXTEC nut, outer flange and cut-off wheel.

5.Check the two (2) wheel flanges to be sure they are in good condi- tion. Remove any nicks or burrs, which could cause uneven cutting pressure and result in wheel damage.

6.Install the cut-off wheel, outer flange and FIXTEC nut (Fig. 1).

7.Press down the spindle lock lever while tightening the FIXTEC nut (clockwise).

NOTE: Hand tighten the FIXTEC nut firmly, but do not use excessive pressure. Overtightening the FIXTEC nut may damage the wheel and flanges. Do not use any tool to tighten the FIXTEC nut. Hand tighten only.

8.Check the wheel for free rotation after installation.

9.Allow the moveable portion of the guard to return to its original position.

10.Before starting a cut, step back and out of line from the tool wheel and make a trial run to confirm that the wheel is in good condition. When replacing a cut-off wheel, run the tool for over 3 minutes. When starting routine work, run the tool for over 1 minute.

Adjusting the Depth of Cut (Fig. 2)

Use the depth adjustment to change the depth of cut. When adjusted properly, the depth adjustment bolt prevents the cut-off wheel from contacting the surface under the base during cutting. Cut-off wheels wear down as they are used and the depth of cut may need to be increased.

1.To adjust the depth of cut, loosen the wing nut.

2.Turn the depth adjustment bolt to achieve the desired depth of cut.

3.Tighten the wing nut.

Fig. 2

Depth adjustment bolt

Wing nut

Using the Quick Release Lever (Fig. 3)

Fig. 3 Release

Lock

1.To release the quick release lever, rotate the lever fully to the left.

2.To lock the quick release lever, rotate the lever fully to the right.

page 6

Image 6
Contents Operators Manual Personal Safety General Safety Rules Read and Understand ALL InstructionsElectrical Safety Work AreaWheel Instructions ServiceSpecific Safety Instructions Abrasive CUT-OFF Machines Machine InstructionsFunctionaldescription Min Arbor Wheel Wheel RPM Hole Size Rating Thickness 4300Grounding Guidelines for Using Extension CordsRecommended Minimum Wire Gauge For Extension Cords Extension CordsAdjusting the Depth of Cut Fig Using the Fixtec NutRemoving and Installing Cut-Off Wheels Fig Using the Quick Release Lever FigUsing the Lock-out Hole Fig Selecting a WorkpieceStarting and Stopping the Tool Five Year Tool Limited Warranty MaintenanceAccessories RepairsSécuritéélectrique Utilisation ET Entretien DES OutilsRéparation Instructions relatives aux disquesInstructions relatives à l’outil Descriptionfonctionnelle Ampères DarbreCordons DE Rallonge Calibres minimaux recommandés pour Les cordons de rallongeMise À LA Terre Avertissement Directives pour l’emploi des cordons de rallongeManiement Avertissement Réglage de la profondeur de coupe FigLutilisation du levier à dégagement rapide Fig Démarrage et arrêt de l’outil LameSélection d’une pièce Lutilisation du Trou de Serrure-Hors FigGarantie Limitée DE L’OUTIL DE Cinq ANS Maintenance AvertissementAccessoires Avertissement RéparationsGuarde Estas Instrucciones Area DE Trabajo SeguridadelectricaSeguridadpersonal EL USO Y Mantenimiento DE LA Herramienta ServicioInstrucciones para el disco abrasivo Instrucciones de la herramientaEspecificaciones de la Tronzadora Descripión FuncionalTierra ¡ADVERTENCIA Extensiónes EléctricasGuías para el uso de cables de extensión Operacion ¡ADVERTENCIA Ajuste de la profundidad de corte FigUsar la palanca de liberación rápida Fig Arranque y paro de la herramienta La hojaCómo seleccionar una pieza de trabajo Usar el hoyo de cierre patronal FigGarantía Limitada DE Cinco Años Mantenimiento ¡ADVERTENCIAAccesorios ¡ADVERTENCIA Mantenimiento de las herramientasSawdust