Wilton FK350-2SX, FK350-4 manual Features

Page 8

Features

Miter Cutting Head

The miter cutting head is the unit that cuts the material and consists of a cast iron base, blade support unit and guard, transmission unit, and motor. The depth of cut is set by adjusting the depth cut stop. The miter cutting head swivels and locks into -45º, 90º, and +45º by means of a locking mechanism. Depressing the mechanism overrides the lock, permitting the head to adjust to any position between -45º and +45θ.

Miter Position Lock

The miter position lock secures the miter cutting head from movement. The miter is secured when the lock is pushed all the way to the left and can be positioned when the lock is moved to the right.

Self-centering Vise

The self-centering vise holds the work piece in place during cutting. The work piece is secured in the vise by turning the vise handles.

FK350 Controls

The control panel consists of the Power (On/Off) switch and High/Stop/Low switch, and an integral coolant system. To operate the machine, the Power switch must be set to on and the High/Stop/Low switch must be set for Hi or Low. Then depress the trigger handle to start.

FK350-SX Controls

This machine features a 2-speed motor, feed speed control, an integral coolant system, and two modes of operation; manual mode, and semi-automatic mode. In semi-auto, the complete cut cycle is initiated via push button. The semi-auto cut cycle closes the vise clamping the material, powers the head down completing the cut, then raises the head, and opens the vise. In manual mode, head up/down, and vise open/close is initiated by switches.

Trigger Handle

The trigger handle (Figure 1) is located on the operating lever used to raise and lower the saw. It contains a micro-switch, which is activated when the operator depresses the run trigger.

Figure 1

Flood Coolant System

The coolant pump must be submerged before operating to prevent damage to the pump.

Coolant is dispensed directed onto the saw blade from a coolant fitting on the upper blade guard. Coolant is provided through tubing from the coolant pump (Figure 2) in the machine base.

Adjust the coolant flow valve on coolant fitting to achieve desired flow. When the coolant switch is in the ON position, flow starts when the drive motor is started. Turning off the coolant switch stops coolant flow.

This coolant system can operate with either a soluble oil base coolant or water-soluble synthetic coolant. Coolant should be changed regularly. Some recommended brands are DoAll and Lenox. These coolants are available at your local industrial distributor.

Figure 2

8

Image 8
Contents Cold Saw Warranty and Service WarrantyTable of Contents Page Page Cutting Capacity All Models SpecificationsIntroduction FK350 Features Features Installation Electrical ConnectionsUnpacking the machine Anchoring and handling the machineControls Control Panel FK350Trigger Handle FK350 Control Panel FK350-SXFK350-SX OperationFK350 Depth Stop FK350 Miter AdjustmentTrip Adjustment FX350-SX Maintenance Lubrication Coolant SystemGeneral Characteristics Blade SelectionDetermining Proper Tooth Pitch Cutting and Feeding SpeedTeeth Shape Blade StructureTypes of Blades Page Troubleshooting Troubleshooting Blade and Cutting ProblemsParts Troubleshooting Machine Fault & Operating ProblemsOrdering Replacement Parts Head Assembly FK350 & FK350-SX Index No. Part No Description Size QtyHead Assembly FK350 & FK350-SX Power Feed Assembly FK350-SX Power Feed Assembly FK350-SX Stock Stop Assembly Stand Assembly FK350 Stand Assembly FK350-SX Stand Assembly FK350-SX Base Assembly FK350 TS-223A911Base Assembly FK350 Base Assembly FK350-SX Base Assembly FK350-SX Manual Vise Assembly FK350 Manual Vise Assembly FK350 Power Vise Assembly FK350-SX File Guard Assembly FK350 & FK350-SX TS-1521021Guard Assembly FK350, FK350-2SX In-Feed Table Assembly Out-Feed Table TS-1502071Pneumatic Drawing FK350-SX Wiring Diagram FK350 Wiring Diagram FK350-SX Page Page WMH Tool Group