Skil MAG77LT manual Additional Safety Warnings, Some dust created by power

Page 5

SM 1619X04759 11-12_SM 1619X04759 11-12.qxp 11/20/12 2:05 PM Page 5

accidentally dropped, lower guard may be bent. Raise the lower guard only with the lower guard lift lever and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.

Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.

Lower guard should be retracted manually only for special cuts such as “Plunge Cuts” and “Compound Cuts”. Raise lower guard by Lower Guard Lift lever and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically.

Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

Do not run the tool while carrying it at your side. Lower guard may be opened by a contact with your clothing. Accidental contact with the spinning saw blade could result in serious personal injury.

Periodically remove the blade, clean the upper, lower guards and the hub area with kerosene and wipe it dry, or blow it clean with compressed air. Preventive maintenance and properly operating guard will reduce the probability of an accident.

Additional Safety Warnings

GFCI and personal protection devices like electrician’s rubber gloves and footwear will further enhance your personal safety.

Do not use AC only rated tools with a DC power supply. While the tool may appear to work, the electrical components of the AC rated tool are likely to fail and create a hazard to the operator.

Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely control the power tool.

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

Develop a periodic maintenance schedule for your tool. When cleaning a tool be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched or safety guard return springs may be improperly mounted.

Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may damage plastic parts.

Risk of injury to user. The power cord must only be serviced by a Skil Factory Service Center or Authorized Skil Service Station.

Some dust created by power

!WARNING sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead-based paints,

•Crystalline silica from bricks and cement and other masonry products, and

•Arsenic and chromium from chemically- treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

-5-

Page 4 Page 6
Image 5
Page 4 Page 6
Contents See Voir Ver la página SM 1619X04759 11-12SM 1619X04759 11-12.qxp 11/20/12 205 PMCall Toll Free for Work area safety General Power Tool Safety WarningsElectrical safety Personal safetyService Safety Rules for Circular SawsCutting procedures Many accidents are caused by poorly maintained power toolsVARI-TORQUE Clutch Kickback causes and relatedLower guard function Some dust created by power Additional Safety WarningsName Designation/Explanation SymbolsSymbols Pivot Stud Bevel Adjustment Lever Blade Stud Contour Functional Description and SpecificationsCircular Saws Calibrated Depth BracketSpring Auxiliary Handle Upper Guard AssemblySAW Shaft Inner WasherOperating Instructions SET Screw Wrench Usage Maximum Depth of CUT StabilityWrench Slotted Driver Correct IncorrectGeneral Cuts SwitchCutting MASONRY/METAL Plunge CutsWrong Cutting Large SheetsRight RIP Cuts RIP Board GuideCleaning MaintenancePreventive maintenance Tool LubricationCare of Blades AccessoriesExtension Cords Trouble Shooting Sécurité électrique Sécurité du lieu de travailUtilisation et entretien des outils Électroportatifs Consignes de sécurité pour scies circulairesEntretien Procédures de coupeEmbrayage VARI-TORQUE Fonction du garde inférieurLe plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesTours, coups, vitesse en surface, orbites La vitesse augmente depuis le réglageSymboles suite Description fonctionnelle et spécifications Graduée en fonction des dimensions Standard du bois d’œuvreScies circulaires Ressort DE ButéeEmbrayage « VARI-TORQUE » Assemblage’ARBRE DE LA Scie Lame Goujon DE Lame Rondelle ExterieureReglage DE LA Profondeur DE Coupe Consignes d’utilisationLevier DE Reglage DE LA Profondeur FIG Levier DE Réglage DU Biseau Guide D’ALIGNEMENTÉjection du diamant du trou pour arbre de la lame coin VIS DE Réglage Utilisation DE LA CLÉCLÉ DE 1/2 PO Coin CLÉ DE 9/16 POCoupes Regulierès InterrupteurMouvement de la garde inférieure Sciage DES Matériaux DE Maçonnerie ET DES MétauxMauvaise Manière Coupe DE Grandes FeuillesBonne Manière Coupes DE Refente Utilisation D’UNE Planche Comme Guide DE RefenteLubrification DE L’OUTIL EntretienBalais DE Charbon PaliersCordons de rallonge AccessoiresLame = équipement de série Clé Sac de transport Guide de refente Sursemelle qui nabîme pasGuide de diagnostic Seguridad personal Seguridad del área de trabajoSeguridad eléctrica Mecánicas Normas de seguridad para sierras circularesServicio de ajustes y reparaciones Procedimientos de corteEmbrague DE PAR Motor Variable RelacionadasArrancar la sierra Función del protector inferior Advertencias de seguridad adicionalesUn número más alto significa mayor velocidad SímbolosSímbolo Nombre Designación/explicación Símbolos continuación Sierras circulares Descripción funcional y especificacionesProtector Superior Boton DE Cierre Inferior Hoja EnsamblajeEl diámetro grande está En el lado de la hoja AflojarInstrucciones de funcionamiento Tornillo DE Ajuste Utilización DE LA Llave DE Tuerca DE Corte MáximaCortes Generales Guía DE InterruptorCorte DE Mampostería Y Metal Cortes POR InmersiónCorrecto Cortes AL Hilo Corte DE Planchas GrandesTABLERO-GUIA Para Cortar AL Hilo Linea DE Corte DeseadaLimpieza MantenimientoServicio Instrucciones DEL Conector QUE Traba POR Giro Cordones de extensiónAccesorios Avería LA Sierra no Arranca Resolución de problemasAvería LA Hoja no Alcanza Toda SU Velocidad Avería Vibración ExcesivaRemarques Notas 1619X04759

MAG77LT specifications

The Skil MAG77LT is a powerful and versatile tool designed for both professional contractors and DIY enthusiasts. This magnesium-framed circular saw is a standout in the market, combining lightweight design with the ability to handle tough cutting tasks with ease. Weighing just 8.5 pounds, the MAG77LT is among the lightest saws in its class, making it easy to transport and maneuver, especially during extended use.

One of the key features of the Skil MAG77LT is its robust 15-amp motor, which delivers an impressive speed of up to 5,300 RPM. This high speed ensures that the saw can make quick and clean cuts through various materials such as plywood, laminate, and hardwood. The tool is equipped with a 7-1/4 inch carbide-tipped blade, which not only enhances cutting efficiency but is also durable enough to withstand rigorous use.

Featuring a magnesium housing, the MAG77LT is designed for maximum durability without sacrificing weight. Magnesium is known for its strength-to-weight ratio, making this saw resistant to significant wear and tear. The ergonomic design of the tool also includes a comfortable grip, allowing users to maintain control even during extended cutting sessions.

Another notable technological advancement in the Skil MAG77LT is its built-in dust blower, which helps keep the cutting line clear of debris. This feature enhances visibility and precision, ensuring that users can make accurate cuts without interruptions. The saw also includes an adjustable bevel capacity that allows for precise angled cuts, with settings ranging up to 56 degrees.

Further enhancing its usability, the Skil MAG77LT features an integrated safety switch. This ensures that the saw won't accidentally start, providing an extra layer of protection for the user. Additionally, the saw's power cord is designed to be flexible, reducing the risk of tangling and allowing for greater freedom of movement while cutting.

In summary, the Skil MAG77LT is a top-tier circular saw that beautifully marries lightweight design with powerful performance. It caters to a wide array of cutting tasks, making it an ideal choice for both professionals and DIYers. With features like a powerful motor, durable magnesium construction, versatile bevel adjustments, and user-friendly safety features, the MAG77LT continues to stand out as a reliable and efficient cutting tool in the market.
Top Page Image Contents