Siemens L-850D/E F-Range Style 2 Inset Lights manual Equipment data

Page 9

L-850D/E F-Range Style 2 Inset Lights

General Information and Requirements

Equipment data

Equipment

Each unit is supplied completely assembled, tested and sealed, ready for

supplied

installation. The electrical connection is made via 1, 2 or 3 cable assemblies with

 

FAA L-823 style 2-pole plugs. The 6 mounting screws (A1) and lock washers (A2)

 

or self locking nuts for holding the light on the base or adapter ring are included.

 

They can be either M10 or 3/8” UNC, according to order. An o-ring gasket (E6) is

 

also included.

 

Each unit is individually packed in a durable, cushioned and corrugated cardboard

 

box, labelled with Siemens Airfield Solutions and ordering numbers.

 

At least one instruction manual is delivered per order.

 

 

Film disc cut-

For some applications, optional film disc cut-outs are available. They form an

out

electrical bypass over the lamp within 15 seconds after lamp failure. After a lamp

 

failure, the film disc cut-out must be replaced.

 

 

References

Ordering codes and reference data pertinent to the light fixture and its components

 

are listed in the tables on pages 30 to 44.

 

 

Differences

All the inset lights used for a particular function look externally identical. The

between

differences between versions depend on the beam colour and the optical support

versions

inside. Make sure to use the correct version when installing the light onto its base.

 

 

Beam color

The colors of the light beams are identified by colored points on the top of the

 

window. A red point, for example, refers to a corresponding red colored beam.

In the 12” F-Range inset lights, light beam coloration is obtained by a dichroïc coating applied on the inner face of the prism. Therefore, no separate color filters are required.

2002 Siemens Airfield Solutions, Incorporated

96A0266D

7

All rights reserved

Issued 2/02

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Siemens Airfield Solutions 850D/E F-Range Style Inset Lights Revision Description Editor Checked Date Record of ChangesSafety precautions Safety InstructionsWarranty Parts Identification Comments and Proposals Information About this ManualTable of Contents General Information and Requirements Overview General information Equipment data Equipment required for installation and maintenance Label Toe-in InstallationInstallation Overview Organisation Applicable documents General recommendationsTool case Equipment required for installationAttack driver Additional tools and equipmentInstallation on FAA Deep Bases Overview UNC Step Action Installation methodMounting and connection How to mount the light assemblyMaintenance Overview Workshop maintenance and preventive maintenance Field maintenancePreventive maintenance Preventive Maintenance Tasks Interval Check ActionLifting tools ProcedurePreliminary Servicing in the Maintenance Base OverviewHow to open the light assembly How to replace a lamp Film disc cut-out ProcedureIllustration Illustration below clarifies the procedure How to replace a prism How to replace the optical assembly How to replace the cable set assembly Illustration How to close and test the light fixture Problem Possible cause Solution TroubleshootingContents This chapter contains the following topics Topic Introduction Light Assembly Part NumbersAssemblies and Exploded View Overview SeeRemarks AssembliesOrdering code 850ERemark Film disc cutout optional Ordering Code 850DList of tables Fixtures Solutions code 850E850D Cate000 010 020 030 040 050 060 070 080 090 100 Description 1411.40.xxx000 010 020 030 040 050 060 070 Description 1411.41.xxxIllustrations 200 210 220 230 240 250 260 DescriptionPart number 270 280 290 300 310 320 330 270 280 290 300 310 320 330 Toe-in Installation 100 110 120 130 140 150 160 170 180 Solutions partIllustration below shows the 12 F-Range inner covers Screw Tool Loctite Torque Screws OverviewExploded view 12 L-850D/ERange
Top Page Image Contents