English
SPECIFICATIONS
Voltage (by areas)* | (110V, 115V, 120V, 127V, 220V, 230V, 240V) | ||
Power Input* | 110 – 127 V | 660 W | |
220 – 240 V | 740 W | ||
| |||
Max. Cutting Depth | Wood 120 mm | ||
Mild Steel 10 mm | |||
|
| ||
850 – 3000 | |||
Stroke | 26 mm | ||
Min. Cutting Radius | 25 mm | ||
Weight (without cord) | 2.3 kg | ||
|
|
| |
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES |
| ||
(1) | Blades (No. 41, No. 42, No. 123X) | 1 each | |
| Refer to Table 1 for use of the blades. |
| |
(2) | Hexagon bar wrench | 1 | |
(3) | Splinter guard | 1 | |
(4) | Dust | collector | 1 |
(5) | Chip | cover | 1 |
(6) | Shutter | 1 | |
Standard accessories are subject to change without | |||
notice. |
|
| |
OPTIONAL ACCESSORIES ... Sold separately
(1)Various types of blades
Refer to Table 1 for use of the blades.
(2)Guide
(3)Sub base
(4)Bench stand (Model
Optional accessories are subject to change without notice.
APPLICATIONS
◯Cutting various lumber and pocket cutting
◯Cutting mild steel plate, aluminum plate, and copper plate
◯Cutting synthetic resins, such as phenol resin and vinyl chloride
◯Cutting thin and soft construction materials
◯Cutting stainless steel plate (with No. 97 blade)
PRIOR TO OPPERATION
1.Power source
Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate.
2.Power switch
Ensure that the power switch is in the OFF position. If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident.
3.Extension cord
When the work area is removed from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.
4. Changing blades
(1)Open the lever up to the stop. (Fig.
(2)Remove fitted blade.
(3)Insert new blade up to the stop in the balde holder. (Fig.
(4)Close the lever. (Fig.
CAUTION:
◯Be sure to switch power OFF and disconnect the plug from the receptacle when changing blades.
◯Do not open the lever when plunger is moving.
NOTE:
◯Confirm the protrusions of blade inserted to the blade holder surely. (Fig. 2)
◯Confirm the blade located between the groove of
roller. (Fig. 3)
5.Adjusting the blade operating speed
This Jig Saw is equipped with the electric control circuit which enables stepless speed control. To adjust the speed, turn the dial shown in Fig. 4. When the dial is set to “1”, the jig saw operates at the minimum speed (850
the material to be cut and working efficiency.
CAUTION:
At low speed (dial setting: 1 or 2) do not cut a wood with a thickness of more than 10 mm or metal with a thickness of more than 1 mm.
6. Adjusting the orbital operation
(1)This Jig Saw employs orbital operation which moves the blade back and forth, as well as up and down. Set the change knob shown in Fig. 5 to “0” to eliminate the orbital operation (the blade moves only up and down). The orbital operation can be selected in 4 steps from “0” to “III”.
(2)For the hard material, such as a steel plate, etc., decrease the orbital operation. For the soft material, such as lumber, plastic, etc., increase the orbital operation to increase work efficiency. To cut the
material accurately, decrease the orbital operation.
7.Cutting stainless steel plates
This Jig Saw can cut stainless steel plates by using No. 97 blade. Carefully read “Concerning cutting of stainless steel plates” for proper operation.
8.Splinter guard
Using the splinter guard when cutting wood materials will reduce splintering of cut surfaces. Insert the splinter guard in the space on the base, and push it completely. (See Fig. 6)
26