English
HOUSING THE HEXAGONAL BAR WRENCH
It is possible to house the hexagonal bar wrench on the base. (See Fig. 16)
CONNECTING WITH CLEANER
By connecting with cleaner (sold separately) through dust collector and adapter (sold separately), most of dust can be collected.
(1)Remove the hexagonal bar wrench from the base.
(2)Move the base fully forward. (Fig. 9, 10)
(3)Attach the chip cover with the shutter put between the chip cover and gear cover. (Fig. 17)
(4)Connect the dust collector with adapter. (Fig. 18)
(5)Connect the adapter with the nose of cleaner. (Fig. 18)
(6)Insert dust collector into the rear hole or the base until the hook catches in the notch. (Fig. 19)
(7)Press the hook to remove the dust collector.
Table 1 List of appropriate blades
MAINTENANCE AND INSPECTION
1.Inspecting the blade
Continued use of a dull or damaged blade will result in reduced cutting efficiency and may cause overloading of the motor. Replace the blade with a new one as soon as excessive abrasion is noted.
2.Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.
3.Maintenance of the motor
The motor unit winding is the very “heart” of the power tool.
Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.
Material | Blade | No. 1 | No. 1 | No.11 | No. 12, | No. 15 | No. 16, | No. 21 | No. 22 | No. 41 | No. 97 | 123X |
| (Long) (Super Long) |
| 42 |
| 46 |
|
|
|
|
| ||
to be cut |
|
|
|
|
|
|
|
| ||||
Material quality |
|
|
| Thickness of material (mm) |
|
|
| |||||
|
|
|
|
|
|
| ||||||
| General lumber | Below Below | 10 ∼ | Below |
|
| 10 ∼ | 5 ∼ | 10 ∼ |
|
| |
| 105 | 135 | 55 | 20 |
|
| 55 | 40 | 65 |
|
| |
Lumber |
|
|
|
|
| |||||||
|
|
| 5 ∼ | Below |
|
| 5 ∼ | 3 ∼ |
|
|
| |
| Plywood |
|
|
|
|
|
|
| ||||
|
|
| 30 | 10 |
|
| 30 | 20 |
|
|
| |
|
|
|
|
|
|
|
|
| ||||
| Mild steel plate |
|
|
|
| 3 ∼ | Below |
|
|
| 2 ∼ | 1.5 ∼ |
|
|
|
|
| 6 | 3 |
|
|
| 5 | 10 | |
Iron plate |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 1.5 ∼ |
| |
| Stainless steel plate |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| 2.5 |
| |
|
|
|
|
|
|
|
|
|
|
|
| |
| Aluminium copper, |
|
|
|
| 3 ∼ | Below |
|
|
| Below |
|
Nonferrous | brass |
|
|
|
| 12 | 3 |
|
|
| 5 |
|
|
|
|
|
| Height |
|
|
|
| Height | Height | |
metal |
|
|
|
|
|
|
|
|
| |||
Aluminium sash |
|
|
|
| up to |
|
|
|
| up to | up to | |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| 25 |
|
|
|
| 25 | 30 |
| Phenol resin, melamin, |
|
|
|
| 5 ∼ | Below | 5 ∼ | Below |
| 5 ∼ |
|
| resin, etc. |
|
|
|
| 20 | 6 | 15 | 6 |
| 15 |
|
Plastics | Vinyl chloride, |
|
| 5 ∼ | Below | 5 ∼ | Below | 5 ∼ | 3 ∼ |
| 5 ∼ |
|
acryl resin, etc. |
|
| 30 | 10 | 20 | 5 | 30 | 20 |
| 15 |
| |
|
|
|
|
| ||||||||
| Foamed polyethylene, |
|
| 10 ∼ | 3 ∼ | 5 ∼ | 3 ∼ | 10 ∼ | 3 ∼ |
| 5 ∼ |
|
| foamed styrol |
|
| 55 | 25 | 25 | 25 | 55 | 40 |
| 25 |
|
| Card board, |
|
| 10 ∼ | 3 ∼ |
|
| 10 ∼ | 3 ∼ |
|
|
|
| corrugated paper |
|
| 55 | 25 |
|
| 55 | 40 |
|
|
|
Pulp | Hardboard |
|
|
|
| 3 ∼ | Below |
|
|
| 3 ∼ |
|
|
|
|
| 25 | 6 |
|
|
| 25 |
| ||
|
|
|
|
|
|
|
|
|
| |||
| Fiberboard |
|
|
|
|
| Below |
|
|
|
|
|
|
|
|
|
|
| 6 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
NOTE:
◯The minimum cutting radius of No. 1 (Long), No.1 (Super Long), No. 21, No. 22 and No. 41 blades is 100 mm.
◯No. 1 (Long), No.1 (Super Long), No. 11, No. 12, No. 15, No. 16, No. 21, No. 22 and No. 97 blades are sold separately.
28