Harbor Freight Tools 45804 See Figure F, See Figure E, previous, To Attach The Guard Assembly

Page 12

Warning! Be very careful during blade tightening and loosening to avoid contact with the blade.

3.Carefully reach into the Saw Blade opening and remove the Hex Nut (1) and Blade Pad (2) from the Shaft (6) avoiding contact with the blade.

4.Insert the Saw Blade (3) at a slight angle (10°) and place the Blade on the Shaft

(6).

 

 

 

 

 

 

 

NOTE: Make sure the teeth

 

FENCE ASSY. (75)

 

 

 

of the Saw Blade (not

 

 

 

 

 

 

 

included) are pointing

 

 

 

 

 

 

 

toward the FRONT of the

 

 

 

 

 

 

 

Table Saw. Follow the

 

 

 

 

SAW BLADE (3)

 

directional arrow shown

 

 

 

 

 

(not included)

 

on the Saw Blade when

 

 

 

 

 

 

 

mounting the Blade.

 

REAR OF

 

FRONT OF

 

 

 

See Figure F.

 

 

FIGURE F

 

TABLE SAW

 

TABLE SAW

 

 

 

 

 

 

 

 

 

 

5.Place the Blade Pad (2) onto the Shaft (6). Next, hand tighten the Hex Nut (1) onto the Shaft.

6.In order to keep the Saw Blade (3) from turning during this step, use the Open-end Spanner (39) to hold the Blade Pad (2). Then while holding the Open-end Spanner firmly in place, wrench tighten the Hex Nut (1) with the Spanner (38) onto the Shaft

(6) to secure the Saw Blade. Position your hand well away from the blade teeth to avoid injury if your hand was to slip while tightening.

7.Once the Saw Blade (3) is secured onto the Shaft (6), replace the Cover (101) and the two Screws (96).

See Figure E, previous page.

To Attach The Guard Assembly:

1.WARNING! Prior to installing the Guard Assembly (50), make sure theTable Saw is disconnected from its electrical power source.

2.Put the Guard Assembly in place over the table. The Guard Assembly attaches to the mounting post shown in Figure G. Simply slip the Guard Assembly over the mounting post. Place a Spring Washer (62), Washer (64), and Big Washer (61) over the Socket Head Screw (63) and thread into the end of the mounting post. Use the included 4 mm Hex Wrench

(196)to tighten the Socket Head Screw (63). See

Figure H.

SKU 45804

PAGE 12

Mounting

Post

Figure G

Figure H

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Assembly and Operating Information Bench Table SAW 2 HPProduct Specifications General Safety RulesSave this Manual Work AreaElectrical Safety Personal SafetyTool USE and Care Service GroundingGrounded Tools Tools with Three Prong Plugs Figure a Double Insulated Tools Tools with TWO Prong Plugs Extension Cords See Figure CSee Figure C, and Figure D Symbology Specific Safety RulesNever allow the woodstock to to it Unpacking Always use the proper size and type of Saw BladeAssembly Instructions To Install a Saw BladeTo Attach The Bottom Plate To Attach The Guard Assembly See Figure FSee Figure E, previous Mounting PostTo Attach The Fence Assembly Tension Adjustment ScrewTo Adjust The Angle Of The Saw Blade Operating InstructionsTo Raise And Lower The Saw Blade See Figure MTo Adjust The Width Of a Cut Assembly 75 to the right or left. See Figure MProper Placement Of Hands During The Cutting Process See Figure O, nextINSPECTION, MAINTENANCE, and Cleaning Table SAW Overload ProtectionTOP View of Table Manner. See Figure PPlease Read the Following Carefully Parts List a Parts Parts List B Parts Assembly Diagram a Parts Assembly Diagram B Parts Appendix a Mounting Instructions Limited 1 year / 90 Day warranty Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800
Top Page Image Contents