Porter-Cable D24225-049-2 instruction manual To Drain Tank, Oil, Checking, Changing

Page 16

To Drain Tank

NOTE: Operation of the air compressor will cause condensation to build up in the air tank. Always drain tank on a washable surface or in a suitable container to prevent damaging or staining surfaces.

1.Set the On/Auto/Off lever to "OFF".

2.Close the globe valve.

3.Remove the air tool or accessory.

4.Open the globe valve and allow the air to slowly bleed from the air tank until tank pressure is approximately 20 psi.

5.Close the globe valve.

6.Drain water from air tank by opening drain valve (counter-clockwise) on bottom of tank.

Water will condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air

tank rupture.

7.After the water has been drained, close the drain valve (clockwise). The air compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled.

Oil

Checking

1.The oil level should be to the middle of the sight glass (C).

2.If needed remove oil fill plug (A) and slowly add oil until it reaches the middle of the sight glass.

NOTE: Use a air compressor oil such as SAE-30 (API CG/CD heavy duty motor oil). Under extreme winter conditions use SAE-20 weight oil.

Changing

1.Remove the oil fill plug (A).

2.Remove the oil drain plug (B) and drain oil into a suitable container.

3.Replace the oil drain plug (B) and tighten securely

NOTE: Use a air compressor oil such as SAE-30 (API CG/CD heavy duty motor oil). Under extreme winter conditions use SAE-20 weight oil.

4.Slowly add compressor oil until the oil level is in the middle of the sightglass (B). NOTE: When filling the crankcase, the oil flows very slowly into the pump. If the oil is added too quickly, it will overflow and appear to be full. NOTE: Crankcase oil capacity is approximately 40 fluid ounces (1.2 L).

Overfilling with oil will cause premature compressor failure.

Do not overfill.

5.Replace oil fill plug (A) and tighten securely.

C

B

A

D24225

16- ENG

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Instruction Safety Guidelines Definitions Important Safety InstructionsResult in death or serious injury Minor or moderate injury Death or serious injuryHazard Risk of Explosion or FireRisk of Bursting Risk from Flying ObjectsRisk of Electrical Shock Risk to BreathingRisk from Moving Parts Risk of BurnsRisk of Falling Specifications AccessoriesGlossary Duty CycleAssembly Tools Required for AssemblyUnpacking To Add Oil To PumpInstallation To Install Air FilterLocation of the Air Compressor Anchoring of the Air CompressorGrounding Instructions Wiring InstructionsAir Distribution System Typical Compressed AIR Distribution System On/Auto/Off Switch Turn this switch OperationKnow Your Air Compressor Description of Operation Cooling System not shown This compressorHow to Use Your Unit Before Starting Break-in ProcedureHow to Stop Check Valve Pressure ReleaseHow to Start Before Each Start-UpTo Check Safety Valve MaintenanceCustomer Responsibilities To Drain Tank OilChecking ChangingBelt Replacement Air Filter Inspection and ReplacementAdjusting Belt Tension Motor Pulley/Flywheel Alignment Air Compressor Pump Intake and Exhaust ValvesInspect Air Lines and Fittings for Leaks Air compressor Head Bolts TorquingService and Adjustments To Replace or Clean Check ValvePressure Check Relief Tube ValveMotor Additional ServiceScrewdriver Storage Troubleshooting Pressure reading Problem Cause Correction Problem Cause Correction Limited Warranty This Warranty is not Transferable and does not CoverManual de Definiciones DE Normas DE Seguridad Resultar en lesiones menores oModeradas Lesiones seriasInstrucciones Importantes DE Seguridad Peligro Riesgo DE Explosión O IncendioPeligro Riesgo DE Explosión Peligro Riesgo DE Objetos Arrojados POR EL AirePeligro Riesgo DE Descarga Eléctrica Peligro Riesgo DE InhalaciónPeligro Riesgo DE Quemaduras Peligro Riesgo DE Partes MóvilesPeligro Riesgo DE Caida PeligroEspecificaciones GlosarioCiclo DE Servicio AccesoriosEnsamblado DesembalajeHerramientas necesarias para el ensamble Para agregar aceite a la bombaInstalación Ensamblaje del Filtro de airUbicación del compresor de aire Anclaje del compresor de aireInstrucciones para la conexión eléctrica Instrucciones Para Conectar a TierraSistema de distribución de aire De compresores de aire, cabezales o cilindrosSistema Típico DE Distribución DE Aire Operación Conozca su compresor de aireDescripción de operaciones Interruptor On/Auto/Off Mueva esteCómo utilizar su unidad Antes de poner en marchaCómo detenerla Procedimiento para el asentamientoAntes de cada puesta en marcha Cómo poner en marchaMantenimiento Responsabilidades del clienteCómo verificar la válvula de seguridad Riesgo de su ruptura o explosiónCómo drenar el tanque AceiteVerificación CambioCorrea Reemplazo Filtro de Aire Inspección y reemplazoRegulación de la Tensión de la Correa Polea y volante Alineación Tornillos del cabezal del compresor de aire. TorqueServicio Y Ajustes Para reemplazar o limpiar la válvula de retenciónTubo aliviador Válvula ReguladoraMotor Servicio AdicionalDestornillador En posición abierta nada es visibleAlmacenaje Aire, originando un riesgo de ruptura de sus paredesGuía DE Diagnóstico DE Problemas La lectura de la Es normal que ocurra algún Problema Causa Corrección Regulación de la tensión de la Porter-Cable Corporation Manuel dinstructions Mesures DE Sécurité Définitions Consignes DE Sécurité ImportantesOu la mort MoyennesConserver CES Directives Risque D’EXPLOSION OU D’INCENDIERisque D’ÉCLATEMENT Risque DE Projection D’OBJETSRisque DE Choc Électrique Risque PAR InhalationRisque Relié AUX Pièces Mobiles Risque DE BrûluresRisque DE Chute Cycle DE Service AccessoiresLexique No de modèleAssemblage Outils requis pour lassemblageDéballage Parce que le compresseur dair aura tendance à basculerEmplacement du compresseur dair Installation du filtre à airAncrage du compresseur dair Non fourniDirectives de câblage Directives DE Mise À LA TerreSystème de distribution dair Têtes et les cylindresSystème DE Distribution Dair Typique Familiarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Utilisation de lappareil Avant le démarrageArrêt de lappareil Procédures de rodageAvant chaque mise en marche Mise en marcheEntretien Vérification de la soupape de sûretéResponsabilités du consommateur Explosion du réservoir à airVidange du réservoir HuileVérification ChangementCourroie Remplacement Filtre à air Inspection et remplacementRéglage de tension de la courroie Alignement de la poulie motorisée/du volant Boulons de la tête du compresseurRemplacement ou nettoyage de la soupape Réparations ET RéglagesTube de Clapet DétenteMoteur Service d’entretien additionnelTournevis En position fermée, le disque est visible Rangement Dépannage Problème Cause CorrectifAccessoires Exigences en air Le moteur ne Bruit de Garantie Limitée D24225 D24225

D24225-049-2 specifications

The Porter-Cable D24225-049-2 is a versatile tool designed for professionals and DIY enthusiasts alike. Built with durability and performance in mind, this product is widely recognized for its excellent features and advanced technology, making it a popular choice for a variety of applications.

One of the standout characteristics of the D24225-049-2 is its robust 2.5-inch stroke length, which ensures deep material penetration and effective cutting. The tool is equipped with a high-performance motor that delivers consistent power, enabling it to handle tough materials with ease. Its variable speed settings allow users to make adjustments based on the specific requirements of their projects, ensuring optimal results whether cutting through wood, metal, or plastic.

The design of the Porter-Cable D24225-049-2 offers user convenience and comfort. Its lightweight yet sturdy construction ensures that users can handle the tool easily without experiencing fatigue during extended use. Additionally, the ergonomic grip provides exceptional control, enhancing precision when maneuvering through intricate cuts.

In terms of technology, the D24225-049-2 incorporates a quick-change blade system, enabling users to swiftly swap out blades without the need for additional tools. This feature streamlines the workflow, allowing for seamless transitions between different cutting tasks. Compatibility with a wide range of blade styles further increases the tool’s versatility, making it suitable for a broad spectrum of materials and applications.

Safety is also a priority in the design of the D24225-049-2. The tool is equipped with safety features that minimize risks during operation, ensuring that users can work confidently. The inclusion of a pivoting shoe enhances stability while cutting, allowing for better control and improved accuracy.

Furthermore, the Porter-Cable D24225-049-2 is engineered for long-lasting performance, with quality materials that withstand wear and tear. Maintenance is simple, making it easy for users to keep the tool in peak condition.

In summary, the Porter-Cable D24225-049-2 combines power, precision, and practicality in a single package. With its advanced features, user-friendly design, and reliable performance, it is a valuable addition to any tool collection, capable of tackling a variety of projects, from woodworking to metalworking and beyond. Whether you are a professional tradesperson or a hobbyist, this tool is likely to meet and exceed your expectations.
Top Page Image Contents