Porter-Cable D24225-049-2 Grounding Instructions, Wiring Instructions, Air Distribution System

Page 10

5.Place the (4) washers (supplied) between the floor and air compressor feet. If needed, solid shims may be placed between the washers and floor to evenly distribute weight on all four feet. See next figure.

6.Place the (4) 3/8" lag screws through the air compressor feet, washers, shims, and into the anchors.

7.Torque 3/8" lag screws to 7-10 ft.-lbs.

Wiring Instructions

GROUNDING INSTRUCTIONS

This product should be connected to a metallic, permanent wiring system, of an equipment-grounding terminal or lead on the product and comply with national and local electrical codes.

Refer to the product specification found in the front of this manual for the voltage and minimum branch circuit requirements.

RISK OF ELECTRICAL SHOCK. Improper electrical grounding can result in electrical shock. The wiring

should be done by a qualified electrician to comply with national and local electrical codes.

A qualified electrician needs to knows the following before wiring:

1.The amperage rating of the electrical box should be adequate. Refer to the product specifications, found in the front of this manual, for this information.

2.The supply line should have the same electrical characteristics (voltage, cycle, phase) as the motor. Refer to the motor nameplate, on side of motor, for this information.

NOTE: The wiring must be the same as the motor nameplate voltage plus or minus 10%. Refer to local codes for recommended wire sizes, correct wire size, and maximum wire run; undersize wire causes high amp draw and overheating to the motor.

3.The wiring diagram for the magnetic starter box (if equipped) can be found inside the magnetic starter box cover.

Electrical wiring must be located away from hot surfaces such as manifold assembly, compressor outlet tubes,

heads, or cylinders.

Air Distribution System

Plastic or PVC pipe is not designed for use with compressed air. Regardless of its indicated pressure

rating, plastic pipe can burst from air pressure. Use only metal pipe for air distribution lines.

The next figure represents a typical air distribution system. The following are tips to remember when setting up the air compressor’s air distribution system.

D24225

10- ENG

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Instruction Result in death or serious injury Minor or moderate injury Safety Guidelines DefinitionsImportant Safety Instructions Death or serious injuryHazard Risk of Explosion or FireRisk of Bursting Risk from Flying ObjectsRisk of Electrical Shock Risk to BreathingRisk from Moving Parts Risk of BurnsRisk of Falling Glossary SpecificationsAccessories Duty CycleUnpacking AssemblyTools Required for Assembly To Add Oil To PumpLocation of the Air Compressor InstallationTo Install Air Filter Anchoring of the Air CompressorGrounding Instructions Wiring InstructionsAir Distribution System Typical Compressed AIR Distribution System Know Your Air Compressor Description of Operation On/Auto/Off Switch Turn this switchOperation Cooling System not shown This compressorHow to Stop How to Use Your UnitBefore Starting Break-in Procedure Check Valve Pressure ReleaseHow to Start Before Each Start-UpTo Check Safety Valve MaintenanceCustomer Responsibilities Checking To Drain TankOil ChangingBelt Replacement Air Filter Inspection and ReplacementAdjusting Belt Tension Inspect Air Lines and Fittings for Leaks Motor Pulley/Flywheel AlignmentAir Compressor Pump Intake and Exhaust Valves Air compressor Head Bolts TorquingPressure Check Service and AdjustmentsTo Replace or Clean Check Valve Relief Tube ValveMotor Additional ServiceScrewdriver Storage Troubleshooting Pressure reading Problem Cause Correction Problem Cause Correction Limited Warranty This Warranty is not Transferable and does not CoverManual de Moderadas Definiciones DE Normas DE SeguridadResultar en lesiones menores o Lesiones seriasInstrucciones Importantes DE Seguridad Peligro Riesgo DE Explosión O IncendioPeligro Riesgo DE Explosión Peligro Riesgo DE Objetos Arrojados POR EL AirePeligro Riesgo DE Descarga Eléctrica Peligro Riesgo DE InhalaciónPeligro Riesgo DE Caida Peligro Riesgo DE QuemadurasPeligro Riesgo DE Partes Móviles PeligroCiclo DE Servicio EspecificacionesGlosario AccesoriosHerramientas necesarias para el ensamble EnsambladoDesembalaje Para agregar aceite a la bombaUbicación del compresor de aire InstalaciónEnsamblaje del Filtro de air Anclaje del compresor de aireSistema de distribución de aire Instrucciones para la conexión eléctricaInstrucciones Para Conectar a Tierra De compresores de aire, cabezales o cilindrosSistema Típico DE Distribución DE Aire Descripción de operaciones OperaciónConozca su compresor de aire Interruptor On/Auto/Off Mueva esteCómo detenerla Cómo utilizar su unidadAntes de poner en marcha Procedimiento para el asentamientoAntes de cada puesta en marcha Cómo poner en marchaCómo verificar la válvula de seguridad MantenimientoResponsabilidades del cliente Riesgo de su ruptura o explosiónVerificación Cómo drenar el tanqueAceite CambioCorrea Reemplazo Filtro de Aire Inspección y reemplazoRegulación de la Tensión de la Correa Polea y volante Alineación Tornillos del cabezal del compresor de aire. TorqueTubo aliviador Válvula Servicio Y AjustesPara reemplazar o limpiar la válvula de retención ReguladoraDestornillador MotorServicio Adicional En posición abierta nada es visibleAlmacenaje Aire, originando un riesgo de ruptura de sus paredesGuía DE Diagnóstico DE Problemas La lectura de la Es normal que ocurra algún Problema Causa Corrección Regulación de la tensión de la Porter-Cable Corporation Manuel dinstructions Ou la mort Mesures DE Sécurité DéfinitionsConsignes DE Sécurité Importantes MoyennesConserver CES Directives Risque D’EXPLOSION OU D’INCENDIERisque D’ÉCLATEMENT Risque DE Projection D’OBJETSRisque DE Choc Électrique Risque PAR InhalationRisque Relié AUX Pièces Mobiles Risque DE BrûluresRisque DE Chute Lexique Cycle DE ServiceAccessoires No de modèleDéballage AssemblageOutils requis pour lassemblage Parce que le compresseur dair aura tendance à basculerAncrage du compresseur dair Emplacement du compresseur dairInstallation du filtre à air Non fourniSystème de distribution dair Directives de câblageDirectives DE Mise À LA Terre Têtes et les cylindresSystème DE Distribution Dair Typique Familiarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Arrêt de lappareil Utilisation de lappareilAvant le démarrage Procédures de rodageAvant chaque mise en marche Mise en marcheResponsabilités du consommateur EntretienVérification de la soupape de sûreté Explosion du réservoir à airVérification Vidange du réservoirHuile ChangementCourroie Remplacement Filtre à air Inspection et remplacementRéglage de tension de la courroie Alignement de la poulie motorisée/du volant Boulons de la tête du compresseurTube de Clapet Remplacement ou nettoyage de la soupapeRéparations ET Réglages DétenteMoteur Service d’entretien additionnelTournevis En position fermée, le disque est visible Rangement Dépannage Problème Cause CorrectifAccessoires Exigences en air Le moteur ne Bruit de Garantie Limitée D24225 D24225

D24225-049-2 specifications

The Porter-Cable D24225-049-2 is a versatile tool designed for professionals and DIY enthusiasts alike. Built with durability and performance in mind, this product is widely recognized for its excellent features and advanced technology, making it a popular choice for a variety of applications.

One of the standout characteristics of the D24225-049-2 is its robust 2.5-inch stroke length, which ensures deep material penetration and effective cutting. The tool is equipped with a high-performance motor that delivers consistent power, enabling it to handle tough materials with ease. Its variable speed settings allow users to make adjustments based on the specific requirements of their projects, ensuring optimal results whether cutting through wood, metal, or plastic.

The design of the Porter-Cable D24225-049-2 offers user convenience and comfort. Its lightweight yet sturdy construction ensures that users can handle the tool easily without experiencing fatigue during extended use. Additionally, the ergonomic grip provides exceptional control, enhancing precision when maneuvering through intricate cuts.

In terms of technology, the D24225-049-2 incorporates a quick-change blade system, enabling users to swiftly swap out blades without the need for additional tools. This feature streamlines the workflow, allowing for seamless transitions between different cutting tasks. Compatibility with a wide range of blade styles further increases the tool’s versatility, making it suitable for a broad spectrum of materials and applications.

Safety is also a priority in the design of the D24225-049-2. The tool is equipped with safety features that minimize risks during operation, ensuring that users can work confidently. The inclusion of a pivoting shoe enhances stability while cutting, allowing for better control and improved accuracy.

Furthermore, the Porter-Cable D24225-049-2 is engineered for long-lasting performance, with quality materials that withstand wear and tear. Maintenance is simple, making it easy for users to keep the tool in peak condition.

In summary, the Porter-Cable D24225-049-2 combines power, precision, and practicality in a single package. With its advanced features, user-friendly design, and reliable performance, it is a valuable addition to any tool collection, capable of tackling a variety of projects, from woodworking to metalworking and beyond. Whether you are a professional tradesperson or a hobbyist, this tool is likely to meet and exceed your expectations.
Top Page Image Contents