Porter-Cable D24225-049-2 Tools Required for Assembly, Unpacking, To Add Oil To Pump

Page 8

ASSEMBLY

Tools Required for Assembly

1 - 9/16" socket or open end wrench

1 - electric drill

Unpacking

1.Remove all packaging.

It may be necessary to brace or support one side of the outfit when removing the pallet because the air

compressor will have a tendency to tip.

2.Remove and discard the (4) screws and washers holding the compressor to the pallet.

3.With the help of another person carefully remove air compressor from pallet and place on a level surface.

To Add Oil To Pump

Compressors are shipped without oil. A small amount of oil may be present in the pump upon receipt of the air compressor. This is due to plant testing and does not mean the pump

contains oil. Do not attempt to operate this air compressor without first adding oil to the crankcase. Serious damage can result from even limited operation unless filled with oil and broken in correctly. Make sure to closely follow initial start-up procedures.

 

 

 

 

Multi-Viscosity motor oils,

A

 

 

 

 

 

 

 

 

 

 

 

 

like 10W 30, should not be

 

 

 

 

used in an air compressor. They leave carbon

 

deposits on critical components, thus reducing

 

performance and compressor life. Use air

 

compressor oil only.

 

NOTE: Use an air compressor oil such as SAE-30 (API CG/CD heavy duty motor oil). Under extreme winter conditions use SAE-20 weight oil.

1.Place unit on a level surface.

2.Remove oil fill plug (A) and slowly add compressor oil until the oil level is in the middle

of the sightglass (B). NOTE: When filling the crankcase, the oil flows very slowly into the

pump. If the oil is added too quickly, it willB overflow and appear to be full. NOTE:

Crankcase oil capacity is approximately 40 fluid ounces.

3.Replace oil fill plug.

D24225

8- ENG

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Instruction Safety Guidelines Definitions Important Safety InstructionsResult in death or serious injury Minor or moderate injury Death or serious injuryHazard Risk of Explosion or FireRisk of Bursting Risk from Flying ObjectsRisk of Electrical Shock Risk to BreathingRisk of Falling Risk of BurnsRisk from Moving Parts Specifications AccessoriesGlossary Duty CycleAssembly Tools Required for AssemblyUnpacking To Add Oil To PumpInstallation To Install Air FilterLocation of the Air Compressor Anchoring of the Air CompressorAir Distribution System Wiring InstructionsGrounding Instructions Typical Compressed AIR Distribution System On/Auto/Off Switch Turn this switch OperationKnow Your Air Compressor Description of Operation Cooling System not shown This compressorHow to Use Your Unit Before Starting Break-in ProcedureHow to Stop Check Valve Pressure ReleaseHow to Start Before Each Start-UpCustomer Responsibilities MaintenanceTo Check Safety Valve To Drain Tank OilChecking ChangingAdjusting Belt Tension Air Filter Inspection and ReplacementBelt Replacement Motor Pulley/Flywheel Alignment Air Compressor Pump Intake and Exhaust ValvesInspect Air Lines and Fittings for Leaks Air compressor Head Bolts TorquingService and Adjustments To Replace or Clean Check ValvePressure Check Relief Tube ValveScrewdriver Additional ServiceMotor Storage Troubleshooting Pressure reading Problem Cause Correction Problem Cause Correction Limited Warranty This Warranty is not Transferable and does not CoverManual de Definiciones DE Normas DE Seguridad Resultar en lesiones menores oModeradas Lesiones seriasInstrucciones Importantes DE Seguridad Peligro Riesgo DE Explosión O IncendioPeligro Riesgo DE Explosión Peligro Riesgo DE Objetos Arrojados POR EL AirePeligro Riesgo DE Descarga Eléctrica Peligro Riesgo DE InhalaciónPeligro Riesgo DE Quemaduras Peligro Riesgo DE Partes MóvilesPeligro Riesgo DE Caida PeligroEspecificaciones GlosarioCiclo DE Servicio AccesoriosEnsamblado DesembalajeHerramientas necesarias para el ensamble Para agregar aceite a la bombaInstalación Ensamblaje del Filtro de airUbicación del compresor de aire Anclaje del compresor de aireInstrucciones para la conexión eléctrica Instrucciones Para Conectar a TierraSistema de distribución de aire De compresores de aire, cabezales o cilindrosSistema Típico DE Distribución DE Aire Operación Conozca su compresor de aireDescripción de operaciones Interruptor On/Auto/Off Mueva esteCómo utilizar su unidad Antes de poner en marchaCómo detenerla Procedimiento para el asentamientoAntes de cada puesta en marcha Cómo poner en marchaMantenimiento Responsabilidades del clienteCómo verificar la válvula de seguridad Riesgo de su ruptura o explosiónCómo drenar el tanque AceiteVerificación CambioRegulación de la Tensión de la Correa Filtro de Aire Inspección y reemplazoCorrea Reemplazo Polea y volante Alineación Tornillos del cabezal del compresor de aire. TorqueServicio Y Ajustes Para reemplazar o limpiar la válvula de retenciónTubo aliviador Válvula ReguladoraMotor Servicio AdicionalDestornillador En posición abierta nada es visibleAlmacenaje Aire, originando un riesgo de ruptura de sus paredesGuía DE Diagnóstico DE Problemas La lectura de la Es normal que ocurra algún Problema Causa Corrección Regulación de la tensión de la Porter-Cable Corporation Manuel dinstructions Mesures DE Sécurité Définitions Consignes DE Sécurité ImportantesOu la mort MoyennesConserver CES Directives Risque D’EXPLOSION OU D’INCENDIERisque D’ÉCLATEMENT Risque DE Projection D’OBJETSRisque DE Choc Électrique Risque PAR InhalationRisque DE Chute Risque DE BrûluresRisque Relié AUX Pièces Mobiles Cycle DE Service AccessoiresLexique No de modèleAssemblage Outils requis pour lassemblageDéballage Parce que le compresseur dair aura tendance à basculerEmplacement du compresseur dair Installation du filtre à airAncrage du compresseur dair Non fourniDirectives de câblage Directives DE Mise À LA TerreSystème de distribution dair Têtes et les cylindresSystème DE Distribution Dair Typique Description du fonctionnement UtilisationFamiliarisez-vous avec votre compresseur dair Utilisation de lappareil Avant le démarrageArrêt de lappareil Procédures de rodageAvant chaque mise en marche Mise en marcheEntretien Vérification de la soupape de sûretéResponsabilités du consommateur Explosion du réservoir à airVidange du réservoir HuileVérification ChangementRéglage de tension de la courroie Filtre à air Inspection et remplacementCourroie Remplacement Alignement de la poulie motorisée/du volant Boulons de la tête du compresseurRemplacement ou nettoyage de la soupape Réparations ET RéglagesTube de Clapet DétenteTournevis En position fermée, le disque est visible Service d’entretien additionnelMoteur Rangement Dépannage Problème Cause CorrectifAccessoires Exigences en air Le moteur ne Bruit de Garantie Limitée D24225 D24225

D24225-049-2 specifications

The Porter-Cable D24225-049-2 is a versatile tool designed for professionals and DIY enthusiasts alike. Built with durability and performance in mind, this product is widely recognized for its excellent features and advanced technology, making it a popular choice for a variety of applications.

One of the standout characteristics of the D24225-049-2 is its robust 2.5-inch stroke length, which ensures deep material penetration and effective cutting. The tool is equipped with a high-performance motor that delivers consistent power, enabling it to handle tough materials with ease. Its variable speed settings allow users to make adjustments based on the specific requirements of their projects, ensuring optimal results whether cutting through wood, metal, or plastic.

The design of the Porter-Cable D24225-049-2 offers user convenience and comfort. Its lightweight yet sturdy construction ensures that users can handle the tool easily without experiencing fatigue during extended use. Additionally, the ergonomic grip provides exceptional control, enhancing precision when maneuvering through intricate cuts.

In terms of technology, the D24225-049-2 incorporates a quick-change blade system, enabling users to swiftly swap out blades without the need for additional tools. This feature streamlines the workflow, allowing for seamless transitions between different cutting tasks. Compatibility with a wide range of blade styles further increases the tool’s versatility, making it suitable for a broad spectrum of materials and applications.

Safety is also a priority in the design of the D24225-049-2. The tool is equipped with safety features that minimize risks during operation, ensuring that users can work confidently. The inclusion of a pivoting shoe enhances stability while cutting, allowing for better control and improved accuracy.

Furthermore, the Porter-Cable D24225-049-2 is engineered for long-lasting performance, with quality materials that withstand wear and tear. Maintenance is simple, making it easy for users to keep the tool in peak condition.

In summary, the Porter-Cable D24225-049-2 combines power, precision, and practicality in a single package. With its advanced features, user-friendly design, and reliable performance, it is a valuable addition to any tool collection, capable of tackling a variety of projects, from woodworking to metalworking and beyond. Whether you are a professional tradesperson or a hobbyist, this tool is likely to meet and exceed your expectations.
Top Page Image Contents