Porter-Cable D24225-049-2 Air Filter Inspection and Replacement, Belt Replacement

Page 17

Air Filter - Inspection and Replacement

Hot surfaces. Risk of burn. Compressor heads are exposed when filter cover is removed. Allow compressor

to cool prior to servicing.

A dirty air filter will not allow the compressor to operate at full capacity. Keep the air filter clean at all times.

1.Remove the air filter cover.

2.Remove the air filter from filter cover.

IMPORTANT: Do not operate the compressor with the air filter removed.

3.Place new air filter into filter cover. Refer to the "Repair Parts" for the correct part number.

4.Replace air filter cover and lock into place.

Belt - Replacement

(Refer to the Outfit Parts Manual for replacement belt part number.)

Serious injury or damage may occur if parts of the body or loose items get caught in moving parts. Never operate the outfit with the belt guard removed. The belt guard should be removed only

when the AIR compressor power is disconnected.

1.Turn air compressor off, lock out the power supply, and relieve all air pressure from the air tank.

2.Remove the belt guard.

3.Mark pump position on saddle.

4.Loosen the motor mounting screws and slide the motor toward the air compressor.

5.Remove the belt and replace with a new one.

6.See the "Adjust Belt Tension" before tightening motor mounting screws.

Adjusting Belt Tension

1.Slide motor into original position, line the motor up with the mark made earlier on saddle.

2.Tighten two outside motor mounting screws enough to hold the motor in place for checking pulley and

flywheel alignment.

3.The belt should deflect 3/16" at midway between the pulley and the flywheel when a 5 pound

weight is applied at the midway

 

Deflection

point.

 

3.When proper belt tension is achieved, tighten all four motor mounting screws. See Parts manual for torque specifications.

NOTE: Once the engine pulley has been moved from its factory set location, the grooves of the flywheel and pulley must be aligned to within 1/16" to prevent excessive belt wear. Verify the alignment by performing the following Pulley and Flywheel - Alignment.

17- ENG

D24225

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Instruction Important Safety Instructions Safety Guidelines DefinitionsResult in death or serious injury Minor or moderate injury Death or serious injuryRisk of Explosion or Fire HazardRisk from Flying Objects Risk of BurstingRisk to Breathing Risk of Electrical ShockRisk of Falling Risk of BurnsRisk from Moving Parts Accessories SpecificationsGlossary Duty CycleTools Required for Assembly AssemblyUnpacking To Add Oil To PumpTo Install Air Filter InstallationLocation of the Air Compressor Anchoring of the Air CompressorAir Distribution System Wiring InstructionsGrounding Instructions Typical Compressed AIR Distribution System Operation On/Auto/Off Switch Turn this switchKnow Your Air Compressor Description of Operation Cooling System not shown This compressorBefore Starting Break-in Procedure How to Use Your UnitHow to Stop Check Valve Pressure ReleaseBefore Each Start-Up How to StartCustomer Responsibilities MaintenanceTo Check Safety Valve Oil To Drain TankChecking ChangingAdjusting Belt Tension Air Filter Inspection and ReplacementBelt Replacement Air Compressor Pump Intake and Exhaust Valves Motor Pulley/Flywheel AlignmentInspect Air Lines and Fittings for Leaks Air compressor Head Bolts TorquingTo Replace or Clean Check Valve Service and AdjustmentsPressure Check Relief Tube ValveScrewdriver Additional ServiceMotor Storage Troubleshooting Pressure reading Problem Cause Correction Problem Cause Correction This Warranty is not Transferable and does not Cover Limited WarrantyManual de Resultar en lesiones menores o Definiciones DE Normas DE SeguridadModeradas Lesiones seriasPeligro Riesgo DE Explosión O Incendio Instrucciones Importantes DE SeguridadPeligro Riesgo DE Objetos Arrojados POR EL Aire Peligro Riesgo DE ExplosiónPeligro Riesgo DE Inhalación Peligro Riesgo DE Descarga EléctricaPeligro Riesgo DE Partes Móviles Peligro Riesgo DE QuemadurasPeligro Riesgo DE Caida PeligroGlosario EspecificacionesCiclo DE Servicio AccesoriosDesembalaje EnsambladoHerramientas necesarias para el ensamble Para agregar aceite a la bombaEnsamblaje del Filtro de air InstalaciónUbicación del compresor de aire Anclaje del compresor de aireInstrucciones Para Conectar a Tierra Instrucciones para la conexión eléctricaSistema de distribución de aire De compresores de aire, cabezales o cilindrosSistema Típico DE Distribución DE Aire Conozca su compresor de aire OperaciónDescripción de operaciones Interruptor On/Auto/Off Mueva esteAntes de poner en marcha Cómo utilizar su unidadCómo detenerla Procedimiento para el asentamientoCómo poner en marcha Antes de cada puesta en marchaResponsabilidades del cliente MantenimientoCómo verificar la válvula de seguridad Riesgo de su ruptura o explosiónAceite Cómo drenar el tanqueVerificación CambioRegulación de la Tensión de la Correa Filtro de Aire Inspección y reemplazoCorrea Reemplazo Tornillos del cabezal del compresor de aire. Torque Polea y volante AlineaciónPara reemplazar o limpiar la válvula de retención Servicio Y AjustesTubo aliviador Válvula ReguladoraServicio Adicional MotorDestornillador En posición abierta nada es visibleAire, originando un riesgo de ruptura de sus paredes AlmacenajeGuía DE Diagnóstico DE Problemas La lectura de la Es normal que ocurra algún Problema Causa Corrección Regulación de la tensión de la Porter-Cable Corporation Manuel dinstructions Consignes DE Sécurité Importantes Mesures DE Sécurité DéfinitionsOu la mort MoyennesRisque D’EXPLOSION OU D’INCENDIE Conserver CES DirectivesRisque DE Projection D’OBJETS Risque D’ÉCLATEMENTRisque PAR Inhalation Risque DE Choc ÉlectriqueRisque DE Chute Risque DE BrûluresRisque Relié AUX Pièces Mobiles Accessoires Cycle DE ServiceLexique No de modèleOutils requis pour lassemblage AssemblageDéballage Parce que le compresseur dair aura tendance à basculerInstallation du filtre à air Emplacement du compresseur dairAncrage du compresseur dair Non fourniDirectives DE Mise À LA Terre Directives de câblageSystème de distribution dair Têtes et les cylindresSystème DE Distribution Dair Typique Description du fonctionnement UtilisationFamiliarisez-vous avec votre compresseur dair Avant le démarrage Utilisation de lappareilArrêt de lappareil Procédures de rodageMise en marche Avant chaque mise en marcheVérification de la soupape de sûreté EntretienResponsabilités du consommateur Explosion du réservoir à airHuile Vidange du réservoirVérification ChangementRéglage de tension de la courroie Filtre à air Inspection et remplacementCourroie Remplacement Boulons de la tête du compresseur Alignement de la poulie motorisée/du volantRéparations ET Réglages Remplacement ou nettoyage de la soupapeTube de Clapet DétenteTournevis En position fermée, le disque est visible Service d’entretien additionnelMoteur Rangement Problème Cause Correctif DépannageAccessoires Exigences en air Le moteur ne Bruit de Garantie Limitée D24225 D24225

D24225-049-2 specifications

The Porter-Cable D24225-049-2 is a versatile tool designed for professionals and DIY enthusiasts alike. Built with durability and performance in mind, this product is widely recognized for its excellent features and advanced technology, making it a popular choice for a variety of applications.

One of the standout characteristics of the D24225-049-2 is its robust 2.5-inch stroke length, which ensures deep material penetration and effective cutting. The tool is equipped with a high-performance motor that delivers consistent power, enabling it to handle tough materials with ease. Its variable speed settings allow users to make adjustments based on the specific requirements of their projects, ensuring optimal results whether cutting through wood, metal, or plastic.

The design of the Porter-Cable D24225-049-2 offers user convenience and comfort. Its lightweight yet sturdy construction ensures that users can handle the tool easily without experiencing fatigue during extended use. Additionally, the ergonomic grip provides exceptional control, enhancing precision when maneuvering through intricate cuts.

In terms of technology, the D24225-049-2 incorporates a quick-change blade system, enabling users to swiftly swap out blades without the need for additional tools. This feature streamlines the workflow, allowing for seamless transitions between different cutting tasks. Compatibility with a wide range of blade styles further increases the tool’s versatility, making it suitable for a broad spectrum of materials and applications.

Safety is also a priority in the design of the D24225-049-2. The tool is equipped with safety features that minimize risks during operation, ensuring that users can work confidently. The inclusion of a pivoting shoe enhances stability while cutting, allowing for better control and improved accuracy.

Furthermore, the Porter-Cable D24225-049-2 is engineered for long-lasting performance, with quality materials that withstand wear and tear. Maintenance is simple, making it easy for users to keep the tool in peak condition.

In summary, the Porter-Cable D24225-049-2 combines power, precision, and practicality in a single package. With its advanced features, user-friendly design, and reliable performance, it is a valuable addition to any tool collection, capable of tackling a variety of projects, from woodworking to metalworking and beyond. Whether you are a professional tradesperson or a hobbyist, this tool is likely to meet and exceed your expectations.
Top Page Image Contents