Porter-Cable D24225-049-2 How to Use Your Unit, Before Starting Break-in Procedure, How to Stop

Page 13

Check Valve: When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air compressor reaches "cut-out" pressure, the check valve "closes", allowing air pressure to remain inside the air tank.

Pressure Release Valve: The pressure release valve, located on the side of the pressure switch, is designed to automatically release compressed air from the compressor head and the outlet tube when the air compressor reaches "cut-out" pressure or is shut off. The pressure release valve allows the motor to restart freely. When the motor stops running, air will be heard escaping from this valve for a few seconds. No air should be heard leaking when the motor is running, or continuous leaking after unit reaches "cut-out" pressure.

Check Valve

Pressure

Release

Valve

Air Intake Filter (not shown) This filter is designed to clean air coming into the pump. This filter must always be clean and ventilation openings free from obstructions. See "Maintenance".

How to Use Your Unit

How to Stop:

1.Set the On/Auto/Off lever to "OFF".

Before Starting

Break-in Procedure

Serious damage may result if the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced.

1.Make sure the On/Auto/Off lever is in the "OFF" position.

2.Recheck all wiring. Make sure wires are secure at all terminals connections. Make sure all contacts move freely and are not obstructed.

3.Open the globe valve fully to permit air to escape and prevent air pressure build up in the air tank during the break-in period.

4.Move the On/Auto/Off lever to "ON/AUTO" position. The compressor will start.

5.Run the compressor for 20 minutes. Make sure the globe valve is open and there is minimal air pressure build-up in tank.

6.Check all air line fittings and connections/piping for air leaks by applying a soap solution. Correct if necessary. NOTE: Minor leaks can cause the air compressor to overwork, resulting in premature breakdown or inadequate performance.

13- ENG

D24225

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Instruction Important Safety Instructions Safety Guidelines DefinitionsResult in death or serious injury Minor or moderate injury Death or serious injuryRisk of Explosion or Fire HazardRisk from Flying Objects Risk of BurstingRisk to Breathing Risk of Electrical ShockRisk from Moving Parts Risk of BurnsRisk of Falling Accessories SpecificationsGlossary Duty CycleTools Required for Assembly AssemblyUnpacking To Add Oil To PumpTo Install Air Filter InstallationLocation of the Air Compressor Anchoring of the Air CompressorGrounding Instructions Wiring InstructionsAir Distribution System Typical Compressed AIR Distribution System Operation On/Auto/Off Switch Turn this switchKnow Your Air Compressor Description of Operation Cooling System not shown This compressorBefore Starting Break-in Procedure How to Use Your UnitHow to Stop Check Valve Pressure ReleaseBefore Each Start-Up How to StartTo Check Safety Valve MaintenanceCustomer Responsibilities Oil To Drain TankChecking ChangingBelt Replacement Air Filter Inspection and ReplacementAdjusting Belt Tension Air Compressor Pump Intake and Exhaust Valves Motor Pulley/Flywheel AlignmentInspect Air Lines and Fittings for Leaks Air compressor Head Bolts TorquingTo Replace or Clean Check Valve Service and AdjustmentsPressure Check Relief Tube ValveMotor Additional ServiceScrewdriver Storage Troubleshooting Pressure reading Problem Cause Correction Problem Cause Correction This Warranty is not Transferable and does not Cover Limited WarrantyManual de Resultar en lesiones menores o Definiciones DE Normas DE SeguridadModeradas Lesiones seriasPeligro Riesgo DE Explosión O Incendio Instrucciones Importantes DE SeguridadPeligro Riesgo DE Objetos Arrojados POR EL Aire Peligro Riesgo DE ExplosiónPeligro Riesgo DE Inhalación Peligro Riesgo DE Descarga EléctricaPeligro Riesgo DE Partes Móviles Peligro Riesgo DE QuemadurasPeligro Riesgo DE Caida PeligroGlosario EspecificacionesCiclo DE Servicio AccesoriosDesembalaje EnsambladoHerramientas necesarias para el ensamble Para agregar aceite a la bombaEnsamblaje del Filtro de air InstalaciónUbicación del compresor de aire Anclaje del compresor de aireInstrucciones Para Conectar a Tierra Instrucciones para la conexión eléctricaSistema de distribución de aire De compresores de aire, cabezales o cilindrosSistema Típico DE Distribución DE Aire Conozca su compresor de aire OperaciónDescripción de operaciones Interruptor On/Auto/Off Mueva esteAntes de poner en marcha Cómo utilizar su unidadCómo detenerla Procedimiento para el asentamientoCómo poner en marcha Antes de cada puesta en marchaResponsabilidades del cliente MantenimientoCómo verificar la válvula de seguridad Riesgo de su ruptura o explosiónAceite Cómo drenar el tanqueVerificación CambioCorrea Reemplazo Filtro de Aire Inspección y reemplazoRegulación de la Tensión de la Correa Tornillos del cabezal del compresor de aire. Torque Polea y volante AlineaciónPara reemplazar o limpiar la válvula de retención Servicio Y AjustesTubo aliviador Válvula ReguladoraServicio Adicional MotorDestornillador En posición abierta nada es visibleAire, originando un riesgo de ruptura de sus paredes AlmacenajeGuía DE Diagnóstico DE Problemas La lectura de la Es normal que ocurra algún Problema Causa Corrección Regulación de la tensión de la Porter-Cable Corporation Manuel dinstructions Consignes DE Sécurité Importantes Mesures DE Sécurité DéfinitionsOu la mort MoyennesRisque D’EXPLOSION OU D’INCENDIE Conserver CES DirectivesRisque DE Projection D’OBJETS Risque D’ÉCLATEMENTRisque PAR Inhalation Risque DE Choc ÉlectriqueRisque Relié AUX Pièces Mobiles Risque DE BrûluresRisque DE Chute Accessoires Cycle DE ServiceLexique No de modèleOutils requis pour lassemblage AssemblageDéballage Parce que le compresseur dair aura tendance à basculerInstallation du filtre à air Emplacement du compresseur dairAncrage du compresseur dair Non fourniDirectives DE Mise À LA Terre Directives de câblageSystème de distribution dair Têtes et les cylindresSystème DE Distribution Dair Typique Familiarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Avant le démarrage Utilisation de lappareilArrêt de lappareil Procédures de rodageMise en marche Avant chaque mise en marcheVérification de la soupape de sûreté EntretienResponsabilités du consommateur Explosion du réservoir à airHuile Vidange du réservoirVérification ChangementCourroie Remplacement Filtre à air Inspection et remplacementRéglage de tension de la courroie Boulons de la tête du compresseur Alignement de la poulie motorisée/du volantRéparations ET Réglages Remplacement ou nettoyage de la soupapeTube de Clapet DétenteMoteur Service d’entretien additionnelTournevis En position fermée, le disque est visible Rangement Problème Cause Correctif DépannageAccessoires Exigences en air Le moteur ne Bruit de Garantie Limitée D24225 D24225

D24225-049-2 specifications

The Porter-Cable D24225-049-2 is a versatile tool designed for professionals and DIY enthusiasts alike. Built with durability and performance in mind, this product is widely recognized for its excellent features and advanced technology, making it a popular choice for a variety of applications.

One of the standout characteristics of the D24225-049-2 is its robust 2.5-inch stroke length, which ensures deep material penetration and effective cutting. The tool is equipped with a high-performance motor that delivers consistent power, enabling it to handle tough materials with ease. Its variable speed settings allow users to make adjustments based on the specific requirements of their projects, ensuring optimal results whether cutting through wood, metal, or plastic.

The design of the Porter-Cable D24225-049-2 offers user convenience and comfort. Its lightweight yet sturdy construction ensures that users can handle the tool easily without experiencing fatigue during extended use. Additionally, the ergonomic grip provides exceptional control, enhancing precision when maneuvering through intricate cuts.

In terms of technology, the D24225-049-2 incorporates a quick-change blade system, enabling users to swiftly swap out blades without the need for additional tools. This feature streamlines the workflow, allowing for seamless transitions between different cutting tasks. Compatibility with a wide range of blade styles further increases the tool’s versatility, making it suitable for a broad spectrum of materials and applications.

Safety is also a priority in the design of the D24225-049-2. The tool is equipped with safety features that minimize risks during operation, ensuring that users can work confidently. The inclusion of a pivoting shoe enhances stability while cutting, allowing for better control and improved accuracy.

Furthermore, the Porter-Cable D24225-049-2 is engineered for long-lasting performance, with quality materials that withstand wear and tear. Maintenance is simple, making it easy for users to keep the tool in peak condition.

In summary, the Porter-Cable D24225-049-2 combines power, precision, and practicality in a single package. With its advanced features, user-friendly design, and reliable performance, it is a valuable addition to any tool collection, capable of tackling a variety of projects, from woodworking to metalworking and beyond. Whether you are a professional tradesperson or a hobbyist, this tool is likely to meet and exceed your expectations.
Top Page Image Contents