Porter-Cable 4212, 4210 instruction manual PORTER-CABLE Limited ONE Year Warranty

Page 43

WARRANTY

PORTER-CABLE LIMITED

ONE YEAR WARRANTY

Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station. Proof of purchase may be required. This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.

43

Image 43

Contents Supplementary Instructiondovetail JIG Manual Table of Contents Important Safety Instructions Safety Guidelines DefinitionsReplacement Parts Additional Safety RulesBackground Information Miscellaneous Techniques OperationTemplates Mounted to Clamping Boards SetupTHROUGH-DOVETAILS with Clamping Boards Cutting the Tails Cutting the PinsFitting the Joint THROUGH-DOVETAILS with Unlimited Board WidthSet the router bit depth, using the pencil mark from Step Fitting the joint is identical to the previous section a Blind Dovetails with Tail Boards Thicker than 7/8 HALF-BLIND Dovetails with Clamping BoardsWood Grain Cutting the JointUsing a Router Table THROUGH-DOVETAIL Bits Alternate Router BitsTHROUGH-DOVETAIL BIT Combinations Readily Available HALF-BLIND Dovetail BIT Readily Available BOX Joint Bits Readily Available BOX Joint BitsDovetail Dado Bits HALF-BLIND Dovetails with Tail Boards Thicker than 7/8 Mitered THROUGH-DOVETAIL Mitering the PinsMitering the Tails THROUGH-DOVETAIL, SKIPPED-PIN MethodHALF-BLIND DOVETAIL, Skipped PIN Method Cutting the Pins SAW Kerf Allowance Method Cutting the Tails BOX END-TO-END Joints Multiple Spacer MethodEND-TO-END Joints Fitting and Cutting the JointDovetail END-TO-END Joints Drawers with Dovetail DadosHinges with a Drilled Hole Wooden HingesHinges with ROUTER-MADE Grooves Hinges with ROUTER-MADE Grooves Angled Joints Setup with the Template Mounted to the Base of the JIGObtuse Angled Joints Cutting the Tails Setup with the Template Mounted to a Clamping BoardCutting the Pins Acute Angled Joints SLANTED-SIDE Joints COMPOUND-ANGLE Joints Setup Blade Tilt Angle Make Angled CUT Inlayed Through Dovetail Inlayed JointsMake the First Joint CUT OFF the Inlay Board Inlayed HALF-BLIND DovetailMake the Second Joint 100 13/128 050 042 028 014 Inlayed BOX Joint BOX Joint BIT Combinations Tables of Commonly Available Router BIT SizesThrough Dovetail Router BIT Combinations HALF-BLIND Dovetail BitsService Troubleshooting MaintenanceAccessories PORTER-CABLE Limited ONE Year Warranty WarrantyMichigan Canadian PORTER-CABLE Delta Service Centers