Porter-Cable 33-402, 33-400, 33-422, 33-423), 16 Compound Miter Cutting, Out-Ripping, In-Ripping

Page 22

COMPOUND MITER CUTTING

Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation are similar to miter cutting except that the blade is first tilted to the desired angle on the bevel scale before it is clamped in place. Fig. 55 shows a compound miter cutting operation on the radial saw.

RIPPING

IMPORTANT: In certain applications, it may be necessary to use two push sticks, and/or featherboards. Also, if a push stick or other feeding device is necessary to assist in the feeding of material, make certain it is conveniently located so it may be reached easily without having to stretch or reach near the blade.

Ripping involves making a lengthwise cut through a board along the grain. When ripping, the track arm is clamped at “0” on the miter scale. The yoke is then positioned and clamped so that the blade is parallel to the fence. When feeding the material, one edge rides against the fence while the flat side of the board rests on the table. The guard should be lowered on the in-feed side until it almost touches the workpiece (Figs. 56 and 57), to act as a holddown. The splitter and anti-kickback fingers (A) Fig. 56 should be adjusted as described under the section

“ADJUSTING SPLITTER AND ANTI-KICKBACK FINGERS” in this manual. The operators hands should always be well away from and to the side of the blade. When ripping narrow work, always use a push stick as shown in Fig. 58 to push the work between the fence and blade. The workpiece must have one straight edge to follow the fence. If board is bowed, place hollow side down. The cutting-head clamp knob should be securely tightened for all ripping operations.

THE MATERIAL MUST NEVER BE FED

INTO THE OUTFEED END OF THE

BLADE GUARD.

OUT-RIPPING

Out-ripping involves all of the general conditions stated above. The yoke is clamped at right angle to the track arm with the blade guard facing the front of the machine. The cutting-head is positioned on the out-rip scale to the desired setting and clamped in position. The workpiece is fed from the left side of the saw. Fig. 56 shows a typical out-ripping operation on the radial saw.

Fig. 55

A

Fig. 56

B

Fig. 57

IN-RIPPING

In-ripping involves all of the general conditions stated under RIPPING. The yoke is clamped at right angle to the track arm with the blade guard facing the rear of the machine. The cutting-head is positioned on the in-rip scale to the desired setting and clamped in position. The workpiece is fed from the right side of the saw. Fig. 57 shows a typical in-ripping operation on the radial saw.

WHEN RIPPING WORK LESS THAN FOUR INCHES WIDE, USE A PUSH STICK TO COMPLETE THE FEED. (FIG. 58)

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 14, 16, and 18 Long Arm Radial Saws Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules Manual Before Operating the MachineAdditional Specific Safety Rules Carton Contents Functional DescriptionUnpacking and Cleaning Guide to PartsAssembly Cuttinghead and CROSS-CUT Stop to TRACK-ARM Starter BOX to Base Table Boards and FenceAdjusting Table TOP Parallel to TRACK-ARM Blade Guard and Anti Kickback DeviceCutterhead Return Spring Operation Locking Switch in OFF PositionStarting and Stopping SAW Taking Side Motion OUT of OVER-ARM Adjusting Ball Bearings Against Track RodsTightening Yoke Against Bearing Carriage Adjusting Track Rods Adjusting Bevel Clamp Handle Adjusting Blade Square with Table TOPAdjusting TRACK-ARM Clamp Handle Adjusting SAW Travel Square with Fence Adjustable CROSS-CUT Stop Removing Heeling in SAW CUTAdjusting Blade Guard Checking and Adjusting Automatic BrakeWrench Storage Brackets Adjusting Tension on Cuttinghead Return AssemblyUsing a Table Extension Auxiliary Table Board FacingCROSS-CUT Stop CROSS-CUTTINGMiter Cutting OUT-RIPPING Compound Miter CuttingRipping IN-RIPPINGPushstick Constructing a Push StickTroubleshooting Guide Maintenance ServiceAccessories WarrantyPage Page Canadian PORTER-CABLE Delta Service Centers
Top Page Image Contents