Powermatic Troubleshooting for PM2700 Shaper, See also Unsatisfactory Cuts

Page 32

Troubleshooting for PM2700 Shaper

Trouble

Shaper will not start.

Overload kicks out frequently.

Cuts are unsatisfactory.

Cutter does not come up to full speed.

Machine vibrates.

Edge splits off on cross grain cut.

 

Possible Cause

 

Remedy

 

 

 

 

1.

Cord unplugged from the power

1.

Plug in power cord.

 

source.

 

 

2.

Fuse blown or circuited breaker

2.

Replace fuse or reset circuit

 

tripped.

 

breaker.

3.

Cord damaged.

3.

Replace cord.

4.

Reversing switch is in the Off

4.

Turn switch to forward of reverse.

 

position.

 

 

5.

Overload tripped.

5.

Reset overload by depressing red

 

 

 

stop button.

6.

Cabinet door is open.

6.

Close cabinet door.

 

 

 

 

1.

Extension cord or wiring

1.

Replace cord or wiring with proper

 

inadequate size.

 

gauge wire.

2.

Feeding stock too fast.

2.

Reduce feed stock rate.

3.

Cutter needs cleaning or replacing.

3. Clean or replace cutter.

 

See also Unsatisfactory Cuts

 

 

 

below.

 

 

 

 

 

 

1.

Dull cutter.

1.

Replace cutter.

2.

Cutterhead rotating in wrong

2.

Check for proper rotation at startup.

 

direction.

 

 

3.

Feeding work in wrong direction.

3.

Feed work against the cutter

 

 

 

rotation.

4.

Gum or pitch on cutter.

4.

Remove cutter and clean with

 

 

5.

Gum or pitch on table causing

 

solvent.

 

erratic feed.

5.

Clean table with solvent.

 

 

 

 

1.

Shop wire gauge is too small.

1.

Replace wiring with proper gauge

 

 

 

wire.

2.

Extension cord or wiring

2.

Replace wit adequate size cord.

 

inadequate size.

 

 

3.

Power source is not adequate.

3.

Contact your electric utility.

4.

Motor not wired for correct voltage.

4. Refer to motor name place and

 

 

 

wiring diagram for correct wiring.

5.

Spindle is locked with madrel lever.

5. Unlock spindle – see label next to

 

 

 

lover on base.

1.

Stand on uneven surface.

1.

Stand must rest solidly on level

 

 

 

surface. Fasten to floor if

2.

Cutterhead damaged.

 

necessary.

3.

Defective V-belt.

2.

Replace cutterhead.

4.

V-belt incorrectly tensioned.

3.

Replace V-belt.

5.

Bent pulley.

4.

Apply proper tension.

6.

Motor mounted improperly.

5.

Replace pulley.

 

 

6.

Motor must be properly mounted

 

 

 

with snug nuts and bolts.

 

 

 

 

1.

Characteristic of this type of cut.

1.

Make cross grain cuts first, then

 

 

 

finish cut with the grain. Use scrap

 

 

 

block to support end of cut.

 

 

 

 

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model PM2700 Shaper Warranty and Service Warranty PeriodTable of Contents Page Page Figure a Introduction Specifications Unpacking InstallingShipping Contents Assembly Electrical ConnectionsMounting the Fence General InformationVoltage Conversion 3 Phase Shaper only Extension CordsHandwheel Adjustments AdjustmentsFence Assembly Movement Verifying that fences are coplanar Coplanar AdjustmentCoplanar Alignment Ram Dial Calibration Loosen the outfeed fence lock knob BLoosen lock handles C and lock knobs D Spindle Gib AdjustmentFeatherboard Hold-downs Spindle Assembly Installation Spindle Assembly RemovalInstalling the Spindle Assembly Locking the ArborShaper Cutter Installation Router Collet Optional InstallationInstalling the Shaper Cutter Locking the SpindleDrive Belt Tension Belt ReplacementChanging Cutter Speed Precision Miter Gauge Loosen lock handle aDigital Readout Operating ControlsStart/Stop Safety Devices OperationsOverview Grain Direction ConsiderationsUsing the Fence Straight Edge Shaping DimensionDepth of Cut Edge Shaping End ShapingShaping All Sides On-Edge ShapingStraight Line Bevel Shaping Contour Edge Shaping With Collar BearingShaping With Collars Position of CollarsStarting Pin Arcs and Circles Enclosed Edge ShapingTemplates Securing the TemplateSash and Door Shaping Special CutsStacked Cutters Butt Joints Glue Butt JointTongued Joint Drop Leaf JointTenoning Troubleshooting for PM2700 Shaper See also Unsatisfactory CutsOptional Accessories Trouble Possible Cause RemedyOrdering Replacement Parts Table Parts List PartsTable Assembly Drawing Fence Parts List Fence Assembly Drawing Frame and Motor Parts List Frame and Motor Assembly Drawing Elevator Parts List Elevator Assembly Drawing Caster Assembly Parts List Caster Assembly Drawing Spindle Assembly Parts List Spindle Assembly Drawing Cabinet and Base Parts List PM2700-450 Cabinet and Base Magnetic Switch Diagrams 230V, 1PhaseMagnetic Switch 5HP, 230V, 3Phase5HP, 460V, 3Phase MotorNew Sanford Road LaVergne, TN Phone

PM2700 specifications

The Powermatic PM2700 is a powerful and versatile bandsaw designed to meet the needs of both professional woodworkers and enthusiastic hobbyists. This robust machine is known for its exceptional cutting performance, advanced features, and user-friendly design.

One of the standout characteristics of the PM2700 is its impressive motor. Equipped with a 3 HP, 230-volt motor, the bandsaw delivers ample power, ensuring that users can tackle even the most challenging materials with ease. The motor operates smoothly and quietly, which enhances the overall working experience.

The PM2700 features a precision-engineered cast iron frame, which provides stability and reduces vibration during operation. The cast iron table is a generous 21 inches by 27 inches, supporting large workpieces while maintaining accuracy in cuts. Additionally, the table incorporates a high-quality, tilting feature that allows for bevel cuts, expanding the functionality of the bandsaw.

An essential aspect of any bandsaw is its cutting capacity, and the PM2700 excels in this area. It offers a resaw capacity of 12 inches, allowing woodworkers to easily slice through thick material. The machine also features an adjustable blade tensioning system that enables quick and precise adjustments to achieve optimal blade performance.

The PM2700 is equipped with an advanced blade tracking system, which helps in maintaining correct blade alignment during operations. This feature significantly reduces the risk of blade wandering, resulting in cleaner cuts and enhanced accuracy. The easy-to-use blade change system further simplifies maintenance, allowing users to switch blades with minimal effort.

Another notable technology integrated into the PM2700 is the built-in digital readout that provides real-time feedback on blade height adjustments. This digital feature ensures that woodworkers can make precise and repeatable cuts with confidence.

For safety, the bandsaw comes with several important features, including a blade guard and quick-release mechanism. Additionally, its robust construction minimizes the risk of injuries associated with vibrations and instability.

Overall, the Powermatic PM2700 is a top-of-the-line bandsaw that combines power, precision, and safety features, making it an excellent choice for anyone serious about woodworking. With its heavy-duty construction and user-friendly design, it promises to deliver outstanding results and durability for years to come.
Top Page Image Contents