Powermatic PM2700 operating instructions Extension Cords, Voltage Conversion 3 Phase Shaper only

Page 10

This machine must be grounded. Grounding provides a path of least resistance to help divert current away from the operator in case of electrical malfunction.

Make sure the voltage of your power supply matches the specifications on the motor plate of the machine.

The PM2700 Shaper should be connected to a dedicated circuit, and protected by a circuit breaker or time delay fuse, with minimum amp ratings as shown in Table 1. Local codes take precedence over recommendations.

Model

Recommended circuit*

 

 

1280100C (3HP 1PH 230V)

30 Amp

 

 

1280101C (5HP 1PH 230V)

40 Amp

 

 

1280102C (5HP 3PH 230V)

30 Amp

 

 

1280102C (5HP 3PH 460V)

15 Amp

*subject to local codes

Table 1

Voltage Conversion (3 Phase Shaper only)

On the 3 phase model, to convert from 230V to 460V, replace the 230V switch with the 460V switch (not included, order part no. PM2700-114C), and re-wire the incoming leads to the motor as shown on the diagram inside the cover of the motor junction box. A similar diagram is also included in the back of this manual. (Figure 3 shows a summary of the lead changes for 230V to 460V conversion.) Note: In case of discrepancies, the diagram in the motor junction box should take precedence.

Extension Cords

The use of extension cords is discouraged. Try to position equipment within reach of the power source. If an extension cord becomes necessary, make sure the cord rating is suitable for the amperage listed on the machine's motor plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

The chart in Table 2 shows the correct size cord to use based on cord length and motor plate amp rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Figure 3

 

 

Extension Cord Length *

 

 

 

 

 

 

 

 

Amps

25

50

75

100

150

200

feet

feet

feet

feet

feet

feet

 

 

 

 

 

 

 

< 5

16

16

16

14

12

12

 

 

 

 

 

 

 

5 to 8

16

16

14

12

10

NR

 

 

 

 

 

 

 

8 to 12

14

14

12

10

NR

NR

 

 

 

 

 

 

 

12 to 15

12

12

10

10

NR

NR

 

 

 

 

 

 

 

15 to 20

10

10

10

NR

NR

NR

 

 

 

 

 

 

 

21 to 30

10

NR

NR

NR

NR

NR

 

 

 

 

 

 

 

*based on limiting the line voltage drop to 5V at 150% of the rated amperes.

NR: Not Recommended.

Table 2

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model PM2700 Shaper Warranty and Service Warranty PeriodTable of Contents Page Page Figure a Introduction Specifications Shipping Contents InstallingUnpacking Mounting the Fence AssemblyElectrical Connections General InformationVoltage Conversion 3 Phase Shaper only Extension CordsFence Assembly Movement AdjustmentsHandwheel Adjustments Coplanar Alignment Coplanar AdjustmentVerifying that fences are coplanar Ram Dial Calibration Loosen the outfeed fence lock knob BFeatherboard Hold-downs Spindle Gib AdjustmentLoosen lock handles C and lock knobs D Installing the Spindle Assembly Spindle Assembly InstallationSpindle Assembly Removal Locking the ArborInstalling the Shaper Cutter Shaper Cutter InstallationRouter Collet Optional Installation Locking the SpindleChanging Cutter Speed Belt ReplacementDrive Belt Tension Precision Miter Gauge Loosen lock handle aStart/Stop Operating ControlsDigital Readout Overview Safety DevicesOperations Grain Direction ConsiderationsUsing the Fence Depth of Cut DimensionStraight Edge Shaping Shaping All Sides Edge ShapingEnd Shaping On-Edge ShapingStraight Line Bevel Shaping Contour Edge Shaping With Collar BearingShaping With Collars Position of CollarsStarting Pin Arcs and Circles Enclosed Edge ShapingTemplates Securing the TemplateStacked Cutters Special CutsSash and Door Shaping Tongued Joint Butt JointsGlue Butt Joint Drop Leaf JointTenoning Troubleshooting for PM2700 Shaper See also Unsatisfactory CutsOptional Accessories Trouble Possible Cause RemedyOrdering Replacement Parts Table Parts List PartsTable Assembly Drawing Fence Parts List Fence Assembly Drawing Frame and Motor Parts List Frame and Motor Assembly Drawing Elevator Parts List Elevator Assembly Drawing Caster Assembly Parts List Caster Assembly Drawing Spindle Assembly Parts List Spindle Assembly Drawing Cabinet and Base Parts List PM2700-450 Cabinet and Base Magnetic Switch Diagrams 230V, 1PhaseMagnetic Switch 5HP, 230V, 3Phase5HP, 460V, 3Phase MotorNew Sanford Road LaVergne, TN Phone

PM2700 specifications

The Powermatic PM2700 is a powerful and versatile bandsaw designed to meet the needs of both professional woodworkers and enthusiastic hobbyists. This robust machine is known for its exceptional cutting performance, advanced features, and user-friendly design.

One of the standout characteristics of the PM2700 is its impressive motor. Equipped with a 3 HP, 230-volt motor, the bandsaw delivers ample power, ensuring that users can tackle even the most challenging materials with ease. The motor operates smoothly and quietly, which enhances the overall working experience.

The PM2700 features a precision-engineered cast iron frame, which provides stability and reduces vibration during operation. The cast iron table is a generous 21 inches by 27 inches, supporting large workpieces while maintaining accuracy in cuts. Additionally, the table incorporates a high-quality, tilting feature that allows for bevel cuts, expanding the functionality of the bandsaw.

An essential aspect of any bandsaw is its cutting capacity, and the PM2700 excels in this area. It offers a resaw capacity of 12 inches, allowing woodworkers to easily slice through thick material. The machine also features an adjustable blade tensioning system that enables quick and precise adjustments to achieve optimal blade performance.

The PM2700 is equipped with an advanced blade tracking system, which helps in maintaining correct blade alignment during operations. This feature significantly reduces the risk of blade wandering, resulting in cleaner cuts and enhanced accuracy. The easy-to-use blade change system further simplifies maintenance, allowing users to switch blades with minimal effort.

Another notable technology integrated into the PM2700 is the built-in digital readout that provides real-time feedback on blade height adjustments. This digital feature ensures that woodworkers can make precise and repeatable cuts with confidence.

For safety, the bandsaw comes with several important features, including a blade guard and quick-release mechanism. Additionally, its robust construction minimizes the risk of injuries associated with vibrations and instability.

Overall, the Powermatic PM2700 is a top-of-the-line bandsaw that combines power, precision, and safety features, making it an excellent choice for anyone serious about woodworking. With its heavy-duty construction and user-friendly design, it promises to deliver outstanding results and durability for years to come.
Top Page Image Contents