Powermatic PM2700 operating instructions

Page 4

1.Read and understand the entire owner's manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This shaper is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a shaper, do not use until proper training and knowledge have been obtained.

5.Do not use this shaper for other than its intended use. If used for other purposes, Powermatic disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this shaper. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this shaper, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, shaping, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead based paint.

•Crystalline silica from bricks, cement and other masonry products.

•Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the machine is properly grounded.

12.Make all machine adjustments or maintenance with the machine unplugged from the power source. A machine under repair should be RED TAGGED to show it must not be used until maintenance is complete.

13.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

14.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

15.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

16.Provide for adequate space surrounding work area and non-glare, overhead lighting.

17.Keep the floor around the machine clean and free of scrap material, oil and grease.

18.Keep visitors a safe distance from the work area. Keep children away.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model PM2700 Shaper Warranty and Service Warranty PeriodTable of Contents Page Page Figure a Introduction Specifications Shipping Contents InstallingUnpacking Assembly Electrical ConnectionsMounting the Fence General InformationVoltage Conversion 3 Phase Shaper only Extension CordsFence Assembly Movement AdjustmentsHandwheel Adjustments Coplanar Alignment Coplanar AdjustmentVerifying that fences are coplanar Ram Dial Calibration Loosen the outfeed fence lock knob BFeatherboard Hold-downs Spindle Gib AdjustmentLoosen lock handles C and lock knobs D Spindle Assembly Installation Spindle Assembly RemovalInstalling the Spindle Assembly Locking the ArborShaper Cutter Installation Router Collet Optional InstallationInstalling the Shaper Cutter Locking the SpindleChanging Cutter Speed Belt ReplacementDrive Belt Tension Precision Miter Gauge Loosen lock handle aStart/Stop Operating ControlsDigital Readout Safety Devices OperationsOverview Grain Direction ConsiderationsUsing the Fence Depth of Cut DimensionStraight Edge Shaping Edge Shaping End ShapingShaping All Sides On-Edge ShapingStraight Line Bevel Shaping Contour Edge Shaping With Collar BearingShaping With Collars Position of CollarsStarting Pin Arcs and Circles Enclosed Edge ShapingTemplates Securing the TemplateStacked Cutters Special CutsSash and Door Shaping Butt Joints Glue Butt JointTongued Joint Drop Leaf JointTenoning Troubleshooting for PM2700 Shaper See also Unsatisfactory CutsOptional Accessories Trouble Possible Cause RemedyOrdering Replacement Parts Table Parts List PartsTable Assembly Drawing Fence Parts List Fence Assembly Drawing Frame and Motor Parts List Frame and Motor Assembly Drawing Elevator Parts List Elevator Assembly Drawing Caster Assembly Parts List Caster Assembly Drawing Spindle Assembly Parts List Spindle Assembly Drawing Cabinet and Base Parts List PM2700-450 Cabinet and Base Magnetic Switch Diagrams 230V, 1PhaseMagnetic Switch 5HP, 230V, 3Phase5HP, 460V, 3Phase MotorNew Sanford Road LaVergne, TN Phone

PM2700 specifications

The Powermatic PM2700 is a powerful and versatile bandsaw designed to meet the needs of both professional woodworkers and enthusiastic hobbyists. This robust machine is known for its exceptional cutting performance, advanced features, and user-friendly design.

One of the standout characteristics of the PM2700 is its impressive motor. Equipped with a 3 HP, 230-volt motor, the bandsaw delivers ample power, ensuring that users can tackle even the most challenging materials with ease. The motor operates smoothly and quietly, which enhances the overall working experience.

The PM2700 features a precision-engineered cast iron frame, which provides stability and reduces vibration during operation. The cast iron table is a generous 21 inches by 27 inches, supporting large workpieces while maintaining accuracy in cuts. Additionally, the table incorporates a high-quality, tilting feature that allows for bevel cuts, expanding the functionality of the bandsaw.

An essential aspect of any bandsaw is its cutting capacity, and the PM2700 excels in this area. It offers a resaw capacity of 12 inches, allowing woodworkers to easily slice through thick material. The machine also features an adjustable blade tensioning system that enables quick and precise adjustments to achieve optimal blade performance.

The PM2700 is equipped with an advanced blade tracking system, which helps in maintaining correct blade alignment during operations. This feature significantly reduces the risk of blade wandering, resulting in cleaner cuts and enhanced accuracy. The easy-to-use blade change system further simplifies maintenance, allowing users to switch blades with minimal effort.

Another notable technology integrated into the PM2700 is the built-in digital readout that provides real-time feedback on blade height adjustments. This digital feature ensures that woodworkers can make precise and repeatable cuts with confidence.

For safety, the bandsaw comes with several important features, including a blade guard and quick-release mechanism. Additionally, its robust construction minimizes the risk of injuries associated with vibrations and instability.

Overall, the Powermatic PM2700 is a top-of-the-line bandsaw that combines power, precision, and safety features, making it an excellent choice for anyone serious about woodworking. With its heavy-duty construction and user-friendly design, it promises to deliver outstanding results and durability for years to come.
Top Page Image Contents