Powermatic pm1000 Installing handwheels and hooks, Installing table extensions

Page 11

1.Remove screws holding saw to pallet, by unscrewing them from underneath pallet.

2.Carefully slide saw from pallet onto floor.

The cabinet saw should be placed in an area with a sturdy level floor, good ventilation and sufficient lighting. Leave enough space around the machine for mounting extension wings and rail assemblies, and loading and off-loading stock and general maintenance work.

Exposed metal surfaces, such as table top and extension wings, have been given a protective coating at the factory. This should be removed with a soft cloth moistened with kerosene or a cleaner- degreaser. Do not use acetone, gasoline, or lacquer thinner for this purpose. Do not use solvents on plastic parts, and avoid using an abrasive pad as it can scratch surfaces.

7.4Installing handwheels and hooks

Refer to Figure 3.

1.Install handwheels (J, Figure 3) onto tilting and raising shafts, as shown. Fit the slot of handwheel hub onto roll pin on shaft, then secure by screwing on a locking knob (H).

2.Install handle (I) onto each handwheel, using 14mm wrench on the flat to tighten it.

3.Install storage hooks (F) with two button head screws and washers (HP-4/5/6). The hooks are used to store the Accu-Fence when it is not in use.

4.Tilt arbor using right handwheel, and remove Styrofoam packing from around motor.

Figure 3

7.5Installing table extensions

Refer to Figure 4.

1.Attach an extension wing to saw table. There is a left and a right version – make sure edge bevel on table extension faces front, to match that of saw table. Use three screws, lock washers and flat washers (HP-1/2/3). Lightly snug screws with 17mm wrench.

(Assembly Tip: If you are doing this without an assistant, lift extension wing vertically to table

edge. Install center screw and washer, and make snug. Then pivot wing parallel to saw table to insert remaining two screws.)

Figure 4

2.Repeat for opposite extension wing. Lightly snug screws.

3.The front edge of extension wings must be flush with front edge of saw table. If needed, tap front edge of wing with a rubber mallet to make flush. See Figure 5.

Figure 5

7.6Leveling table extensions

Refer to Figure 6.

Level extension wings to saw table using a straight edge. A metal straight edge is ideal, though a carefully jointed board may also be used.

Figure 6

11

Image 11
Contents Part No. M-1791000 PowermaticWarranty Period Warranty and ServiceTable of contents Safety warnings Protection Tips from Kickback KickbackKickback Prevention About this manual Glossary Subject to local/national electrical codes SpecificationsCfm 18 cmm Unpacking and cleanup Setup and assemblyShipping contents Tools required for assemblyLeveling table extensions Installing handwheels and hooksInstalling table extensions Motor cover Switch bracketRails and Fence Wood Extension TableRiving knife Installing and removing bladeDust chute Electrical connectionsAnti-kickback pawls Blade guardExtension cords Overload reset buttonMagnetic switch and safety key Voltage conversionBlade raising/tilt mechanism AdjustmentsTools required for adjustments Fence alignmentTilt stop Blade tilt stop adjustmentExtension plate CalibrationLateral alignment Riving knife alignmentBelt tension Belt adjustmentTable to blade alignment Blade proximity alignmentArbor/Arbor Bearing Removal Belt replacementOperations Rip sawing Crosscutting ResawingDo not use the standard table insert for dadoing operations Bevel and miter operationsDado cutting Filler piece Safety devicesFeather board Push Block Template Push stick and push blockMiscellaneous MaintenanceCleaning Lubrication# 708097 Dado Insert Optional accessoriesSymptom Probable Cause Remedy Troubleshooting the PM1000 Cabinet SawReplacement Parts 15.1.1 PM1000 Table and Cabinet Assembly Exploded View Index No Description Size Qty 15.1.2 PM1000 Table and Cabinet Assembly Parts ListIndex No. Part No Description Size Qty 15.2.1 PM1000 Motor and Trunnion Assembly Exploded View PM1000-115RCC 15.2.2 PM1000 Motor and Trunnion Assembly Parts ListJTAS10L-179-3 15.3.1 PM1000 Blade Guard Assembly Exploded View PM1000-AKPA 15.3.2 PM1000 Blade Guard Assembly Parts ListElectrical Connections for PM1000 This page intentionally left blank New Sanford Road LaVergne, Tennessee