Powermatic pm1000 Setup and assembly, Shipping contents, Tools required for assembly

Page 10

7.0Setup and assembly

7.1Shipping contents

7.1.1Carton contents (Figure 1)

1 Cabinet saw

1Guard assembly (A)

1Miter gauge (B)

1Anti-kickback pawl assembly (C)

1Riving knife (D)

1Arbor wrench (E)

2Storage hooks (F)

1Push stick (G)

2Knobs (H)

2 Handles (I)

2Handwheels (J)

1Motor Cover (K)

1Extension wing – Left (L)

1Extension wing – Right (M)

1Insert plate – (N)

1Low profile riving knife – (P)

1Hardware package

1Warranty card

1Operating Instructions and Parts Manual

Figure 1

7.1.2Hardware package (Figure 2)

6Hex cap screws, M10x35 (HP-1)

6Lock washers, M10 (HP-2)

6Flat washers, M10 (HP-3)

4Socket head button screws, M6x16 (HP-4)

4Lock washers, M6 (HP-5)

4Flat washers, M6 (HP-6)

3Socket flat head screws, M6x10 (HP-7)

Figure 2

Note: Fence and rail assemblies, and wood extension tables and legs, are shipped in separate cartons.

Read and understand all assembly instructions before attempting assembly. The saw must be disconnected (unplug!) from power during assembly. Failure to comply may cause serious injury.

7.2Tools required for assembly

Hex keys – 3 and 4mm

Open end wrenches – 14 and 17mm Cross point screwdriver

Straight edge

Rubber mallet (or hammer with block of wood)

Note: A ratchet wrench/socket set may speed assembly time. Additional tools may be needed for assembly of fence and rails – consult Accu-Fence manual.

7.3Unpacking and cleanup

Remove all contents from shipping carton. Remove items from inside cabinet. Do not discard carton or packing material until saw is assembled and running satisfactorily.

Compare contents of your container with above parts lists to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. (Check saw first in case parts were preinstalled.) Read instruction manual thoroughly for assembly, maintenance and safety instructions.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Powermatic Part No. M-1791000Warranty and Service Warranty PeriodTable of contents Safety warnings Kickback Prevention KickbackProtection Tips from Kickback About this manual Glossary Specifications Subject to local/national electrical codesCfm 18 cmm Tools required for assembly Setup and assemblyShipping contents Unpacking and cleanupInstalling table extensions Installing handwheels and hooksLeveling table extensions Wood Extension Table Switch bracketRails and Fence Motor coverInstalling and removing blade Riving knifeBlade guard Electrical connectionsAnti-kickback pawls Dust chuteVoltage conversion Overload reset buttonMagnetic switch and safety key Extension cordsFence alignment AdjustmentsTools required for adjustments Blade raising/tilt mechanismCalibration Blade tilt stop adjustmentExtension plate Tilt stopRiving knife alignment Lateral alignmentBlade proximity alignment Belt adjustmentTable to blade alignment Belt tensionOperations Belt replacementArbor/Arbor Bearing Removal Rip sawing Resawing CrosscuttingDado cutting Bevel and miter operationsDo not use the standard table insert for dadoing operations Feather board Safety devicesFiller piece Push stick and push block Push Block TemplateLubrication MaintenanceCleaning MiscellaneousOptional accessories # 708097 Dado InsertTroubleshooting the PM1000 Cabinet Saw Symptom Probable Cause RemedyReplacement Parts 15.1.1 PM1000 Table and Cabinet Assembly Exploded View 15.1.2 PM1000 Table and Cabinet Assembly Parts List Index No Description Size QtyIndex No. Part No Description Size Qty 15.2.1 PM1000 Motor and Trunnion Assembly Exploded View 15.2.2 PM1000 Motor and Trunnion Assembly Parts List PM1000-115RCCJTAS10L-179-3 15.3.1 PM1000 Blade Guard Assembly Exploded View 15.3.2 PM1000 Blade Guard Assembly Parts List PM1000-AKPAElectrical Connections for PM1000 This page intentionally left blank New Sanford Road LaVergne, Tennessee
Top Page Image Contents