Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual Configuration, Chapter contents

Models: 3088A

1 71

Page 18

Chapter 2	Configuration
Chapter contents
Introduction		19
Software (CLI) configuration		19
Hardware (DIP-switch) configuration		19
Configuring the DIP switches		21
System reset mode		22
DIP switch settings		22
DIP switch settings		23
S4-2 through S4-8: Data Rate		24
DCE/DTE operation		26
Ethernet Management Port		27
Help Commands		29
System Configuration Commands		29
System Status Commands		30
DSL Configuration Commands		30
DSL Status Command		30
DSL Clear Errcntrs Command		30
E1 Configuration Commands		30
E1 Status Commands		31
Remote Console	..............................................................................................................................................	31
Example Command Line Interface Session		31
OnSite Plug ‘n’ Play		33

Page 18

Image 18

Contents

Getting Started Guide OnSite Model 3088A SeriesG.SHDSL.bis CPE with fixed serial interface REGULATORY MODEL NUMBER 03340D4-0017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Table of ContentsSummary Table of Contents Configuration7 Reset configuration to factory defaults OnSite installationSoftware Upgrade OperationSpecifications Factory default valuesCompliance information D Factory replacement parts and accessories Table of ContentsFactory default values for software-configurable parameters Factory replacement parts and accessoriesList of Figures List of Tables About this guide AudienceStructure Note A note presents additional information or interesting sidelights Precautionsimpaired functioning Strictly follow the warning instructions to avoid personal injurySafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations ConventionChapter contents Chapter 1 General informationFeatures OnSite 3088A overviewSerial interface types Power input connector External AC universal power supplyExternal 48 VDC power supply Configuration ChapterChapter contents Software CLI configuration Hardware DIP-switch configurationIntroduction Description Table 2 lists the Model 3088A’s configurable parametersParameter Possible ValuesDescription Configuring the DIP switchesParameter Possible ValuesSystem reset mode DIP switch settingsModel 3088A Function DIP switch settingsPosition FunctionS4-3 S4-2 through S4-8 Data RateS4-2 S4-4S4-4 S4-2S4-3 S4-5DCE/DTE operation Note This section applies to the following 3088A modelsEthernet Management Port DSL Link State In Progress, Success, Deactivated, or Idle E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoAlarms RED, YELLOW, BLUE. Active or Inactive DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing Syncsystem set password password Sets the system password Help CommandsSystem Configuration Commands System Status CommandsDSL Status Command DSL Configuration Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Clear Errcntrs CommandExample Command Line Interface Session Remote Consolesystem show config 2 Configurationsystem save config Model 3088A Series Getting Started GuideOnSite Plug ‘n’ Play OnSite installation Chapter contentsChapter Installation Connecting the twisted pair interfaceConnecting the Model 3088A serial interface Connecting the Model 3088A to a “DCE” or “DTE” deviceConnecting the Model 3088A/K serial interface Connecting the Model 3088A/K to an E1 NetworkConnect twisted pair 120 ohm to E1 network Connecting dual coaxial cable 75 ohm to E1 network G.703/G.704 PowernetworkConnecting power External AC universal power supplyDC Power WARNING ton for assistance” on pageOperation Chapter contentsChapter LED status monitors Power-upPower Green DSL GreenTM/ER Yellow Terminal Green3088A/D with the X.21 interface LOS Red Model /KPatterns The data path for the RDL is shown in figureChapter 5 Remote console operation Chapter contents5. Wait for the message Console Remote console connection established How to ConnectEstablishing a Remote Console Session Introductionsystem show status command shows that DSL link is not up How to DisconnectWe can now enter commands on the remote console Model 3088A Series Getting Started GuideDifferences in Local and Remote Control Session Behavior Figure 18. Remote control session with LAL diagramChapter 6 Software Upgrade Chapter contents2-3 minutes to complete. To upgrade the software IntroductionChapter 7 Reset configuration to factory defaults Chapter contentsIntroduction 1. Turn the Model 3088A offChapter 8 Contacting Patton for assistance Chapter contentsContact information Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Patton support headquarters in the USAReturn for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix A Compliance information Chapter contentsRadio and TV Interference FCC Part SafetyCompliance CE Declaration of ConformityAppendix B Specifications Chapter contentsClocking modes Serial connectorDiagnostics DTE rateTerminal Green ConfigurationPower and power supply specifications 3088A/D with the X.21 interfaceExternal AC universal power supply Transmission lineLine coding External 48 VDC power supplyG.SHDSL physical connection Line rates DSL lineLine interface EnvironmentAppendix C Factory default values Chapter contentsFactory default values for software-configurable parameters Default value Factory default values for software-configurable parametersDefault value ParameterDefault value ParameterAppendix D Factory replacement parts and accessories Chapter contentsFactory replacement parts and accessories Factory replacement parts and accessories Power SuppliesPower Adapters Line port Appendix E Interface pinoutsChapter contents RS-232 interfaceSignal Line portRS-232 interface Signal DesignationSignal V.35 interfaceE1 interface SignalD-sub-15 female connector DTE/DCE orientation X.21 interfaceEthernet Console port Signal

Chapter 2

Configuration