Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual OnSite installation, Chapter contents

Models: 3088A

1 71

Page 34

Chapter 3	OnSite installation
Chapter contents
Installation		35
Connecting the twisted pair interface		35
Connecting the Model 3088A serial interface		36
Connecting the Model 3088A to a “DCE” or “DTE” device		36
Connecting the Model 3088A/K serial interface		37
Connecting the Model 3088A/K to an E1 Network		37
Connect twisted pair (120 ohm) to E1 network		37
Connecting dual coaxial cable (75 ohm) to E1 network		38
Connecting power		39
External AC universal power supply		39
DC Power		40

Page 34

Image 34

Contents

Getting Started Guide OnSite Model 3088A SeriesG.SHDSL.bis CPE with fixed serial interface REGULATORY MODEL NUMBER 03340D4-0017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Table of ContentsSummary Table of Contents Configuration7 Reset configuration to factory defaults OnSite installationSoftware Upgrade OperationFactory default values SpecificationsCompliance information D Factory replacement parts and accessories Table of ContentsFactory default values for software-configurable parameters Factory replacement parts and accessoriesList of Figures List of Tables Audience About this guideStructure Note A note presents additional information or interesting sidelights Precautionsimpaired functioning Strictly follow the warning instructions to avoid personal injurySafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations ConventionChapter contents Chapter 1 General informationOnSite 3088A overview FeaturesSerial interface types Power input connector External AC universal power supplyExternal 48 VDC power supply Chapter ConfigurationChapter contents Hardware DIP-switch configuration Software CLI configurationIntroduction Description Table 2 lists the Model 3088A’s configurable parametersParameter Possible ValuesDescription Configuring the DIP switchesParameter Possible ValuesDIP switch settings System reset modeModel 3088A Function DIP switch settingsPosition FunctionS4-3 S4-2 through S4-8 Data RateS4-2 S4-4S4-4 S4-2S4-3 S4-5DCE/DTE operation Note This section applies to the following 3088A modelsEthernet Management Port DSL Link State In Progress, Success, Deactivated, or Idle E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoAlarms RED, YELLOW, BLUE. Active or Inactive DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing Syncsystem set password password Sets the system password Help CommandsSystem Configuration Commands System Status CommandsDSL Status Command DSL Configuration Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Clear Errcntrs CommandExample Command Line Interface Session Remote Consolesystem show config 2 Configurationsystem save config Model 3088A Series Getting Started GuideOnSite Plug ‘n’ Play Chapter contents OnSite installationChapter Installation Connecting the twisted pair interfaceConnecting the Model 3088A serial interface Connecting the Model 3088A to a “DCE” or “DTE” deviceConnecting the Model 3088A/K to an E1 Network Connecting the Model 3088A/K serial interfaceConnect twisted pair 120 ohm to E1 network Connecting dual coaxial cable 75 ohm to E1 network G.703/G.704 PowernetworkConnecting power External AC universal power supplyDC Power WARNING ton for assistance” on pageChapter contents OperationChapter LED status monitors Power-upPower Green DSL GreenTM/ER Yellow Terminal Green3088A/D with the X.21 interface LOS Red Model /KPatterns The data path for the RDL is shown in figureChapter 5 Remote console operation Chapter contents5. Wait for the message Console Remote console connection established How to ConnectEstablishing a Remote Console Session Introductionsystem show status command shows that DSL link is not up How to DisconnectWe can now enter commands on the remote console Model 3088A Series Getting Started GuideDifferences in Local and Remote Control Session Behavior Figure 18. Remote control session with LAL diagramChapter 6 Software Upgrade Chapter contents2-3 minutes to complete. To upgrade the software IntroductionChapter 7 Reset configuration to factory defaults Chapter contentsIntroduction 1. Turn the Model 3088A offChapter 8 Contacting Patton for assistance Chapter contentsContact information Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Patton support headquarters in the USAReturn for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix A Compliance information Chapter contentsRadio and TV Interference FCC Part SafetyCompliance CE Declaration of ConformityAppendix B Specifications Chapter contentsClocking modes Serial connectorDiagnostics DTE rateTerminal Green ConfigurationPower and power supply specifications 3088A/D with the X.21 interfaceExternal AC universal power supply Transmission lineLine coding External 48 VDC power supplyG.SHDSL physical connection Line rates DSL lineLine interface EnvironmentChapter contents Appendix C Factory default valuesFactory default values for software-configurable parameters Default value Factory default values for software-configurable parametersDefault value ParameterDefault value ParameterChapter contents Appendix D Factory replacement parts and accessoriesFactory replacement parts and accessories Power Supplies Factory replacement parts and accessoriesPower Adapters Line port Appendix E Interface pinoutsChapter contents RS-232 interfaceSignal Line portRS-232 interface Signal DesignationSignal V.35 interfaceE1 interface SignalD-sub-15 female connector DTE/DCE orientation X.21 interfaceEthernet Console port Signal