Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual Parameter, Default value

Models: 3088A

1 71

Page 65

Model 3088A Series Getting Started Guide	C • Factory default values

Table 9. 3088A/K

	Parameter	Default value

Clock Mode		Receive-Recover
DSL Timeslots		31

E1	Timeslots	31
E1	Timeslot Map	1-31

E1	Line Type	E1 - Fractional
E1	Line Code	HDB3

E1	Line Build Out	75 Ohm
E1	Rx Equalizer	Disabled

E1	Pass Framing	Disabled
E1	Pass Alarms	Disabled

Circuit ID		Patton Model 3088A
Password		superuser

Annex		B
Loopback		Off

Pattern		Off

Factory default values for software-configurable parameters

Page 65

Image 65

Patton electronic 3088A manual Parameter, Default value

Contents

G.SHDSL.bis CPE with fixed serial interface OnSite Model 3088A SeriesGetting Started Guide REGULATORY MODEL NUMBER 03340D4-0017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Summary Table of Contents Table of ContentsTable of Contents ConfigurationSoftware Upgrade OnSite installation7 Reset configuration to factory defaults OperationCompliance information SpecificationsFactory default values Factory default values for software-configurable parameters Table of ContentsD Factory replacement parts and accessories Factory replacement parts and accessoriesList of Figures List of Tables Structure About this guideAudience impaired functioning PrecautionsNote A note presents additional information or interesting sidelights Strictly follow the warning instructions to avoid personal injurySafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions ConventionChapter 1 General information Chapter contentsSerial interface types FeaturesOnSite 3088A overview External AC universal power supply Power input connectorExternal 48 VDC power supply Chapter contents ConfigurationChapter Introduction Software CLI configurationHardware DIP-switch configuration Parameter Table 2 lists the Model 3088A’s configurable parametersDescription Possible ValuesParameter Configuring the DIP switchesDescription Possible ValuesModel 3088A System reset modeDIP switch settings Position DIP switch settingsFunction FunctionS4-2 S4-2 through S4-8 Data RateS4-3 S4-4S4-3 S4-2S4-4 S4-5Note This section applies to the following 3088A models DCE/DTE operationEthernet Management Port Alarms RED, YELLOW, BLUE. Active or Inactive E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoDSL Link State In Progress, Success, Deactivated, or Idle DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing SyncSystem Configuration Commands Help Commandssystem set password password Sets the system password System Status Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Configuration CommandsDSL Status Command DSL Clear Errcntrs CommandRemote Console Example Command Line Interface Sessionsystem save config 2 Configurationsystem show config Model 3088A Series Getting Started GuideOnSite Plug ‘n’ Play Chapter OnSite installationChapter contents Connecting the twisted pair interface InstallationConnecting the Model 3088A to a “DCE” or “DTE” device Connecting the Model 3088A serial interfaceConnect twisted pair 120 ohm to E1 network Connecting the Model 3088A/K serial interfaceConnecting the Model 3088A/K to an E1 Network G.703/G.704 Powernetwork Connecting dual coaxial cable 75 ohm to E1 networkExternal AC universal power supply Connecting powerWARNING ton for assistance” on page DC PowerChapter OperationChapter contents Power Green Power-upLED status monitors DSL Green3088A/D with the X.21 interface Terminal GreenTM/ER Yellow LOS Red Model /KThe data path for the RDL is shown in figure PatternsChapter contents Chapter 5 Remote console operationEstablishing a Remote Console Session How to Connect5. Wait for the message Console Remote console connection established IntroductionWe can now enter commands on the remote console How to Disconnectsystem show status command shows that DSL link is not up Model 3088A Series Getting Started GuideFigure 18. Remote control session with LAL diagram Differences in Local and Remote Control Session BehaviorChapter contents Chapter 6 Software UpgradeIntroduction 2-3 minutes to complete. To upgrade the softwareChapter contents Chapter 7 Reset configuration to factory defaults1. Turn the Model 3088A off IntroductionChapter contents Chapter 8 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsContact information Patton support headquarters in the USAReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersChapter contents Appendix A Compliance informationCompliance SafetyRadio and TV Interference FCC Part CE Declaration of ConformityChapter contents Appendix B SpecificationsDiagnostics Serial connectorClocking modes DTE ratePower and power supply specifications ConfigurationTerminal Green 3088A/D with the X.21 interfaceLine coding Transmission lineExternal AC universal power supply External 48 VDC power supplyLine interface Line rates DSL lineG.SHDSL physical connection EnvironmentFactory default values for software-configurable parameters Appendix C Factory default valuesChapter contents Default value Factory default values for software-configurable parametersDefault value ParameterParameter Default valueFactory replacement parts and accessories Appendix D Factory replacement parts and accessoriesChapter contents Power Adapters Factory replacement parts and accessoriesPower Supplies Chapter contents Appendix E Interface pinoutsLine port RS-232 interfaceRS-232 interface Line portSignal Signal DesignationE1 interface V.35 interfaceSignal SignalEthernet Console port X.21 interfaceD-sub-15 female connector DTE/DCE orientation Signal