Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual Remote console operation, Chapter contents

Models: 3088A

1 71

Page 45

Chapter 5 Remote console operation
Chapter contents
Introduction	46
Establishing a Remote Console Session	46
How to Connect	46
How to Disconnect	47
Differences in Local and Remote Control Session Behavior	48

Page 45

Image 45

Contents

G.SHDSL.bis CPE with fixed serial interface OnSite Model 3088A SeriesGetting Started Guide REGULATORY MODEL NUMBER 03340D4-0017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Summary Table of Contents Table of ContentsTable of Contents ConfigurationSoftware Upgrade OnSite installation7 Reset configuration to factory defaults OperationSpecifications Factory default valuesCompliance information Factory default values for software-configurable parameters Table of ContentsD Factory replacement parts and accessories Factory replacement parts and accessoriesList of Figures List of Tables About this guide AudienceStructure impaired functioning PrecautionsNote A note presents additional information or interesting sidelights Strictly follow the warning instructions to avoid personal injurySafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions ConventionChapter 1 General information Chapter contentsFeatures OnSite 3088A overviewSerial interface types External AC universal power supply Power input connectorExternal 48 VDC power supply Configuration ChapterChapter contents Software CLI configuration Hardware DIP-switch configurationIntroduction Parameter Table 2 lists the Model 3088A’s configurable parametersDescription Possible ValuesParameter Configuring the DIP switchesDescription Possible ValuesSystem reset mode DIP switch settingsModel 3088A Position DIP switch settingsFunction FunctionS4-2 S4-2 through S4-8 Data RateS4-3 S4-4S4-3 S4-2S4-4 S4-5Note This section applies to the following 3088A models DCE/DTE operationEthernet Management Port Alarms RED, YELLOW, BLUE. Active or Inactive E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoDSL Link State In Progress, Success, Deactivated, or Idle DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing SyncSystem Configuration Commands Help Commandssystem set password password Sets the system password System Status Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Configuration CommandsDSL Status Command DSL Clear Errcntrs CommandRemote Console Example Command Line Interface Sessionsystem save config 2 Configurationsystem show config Model 3088A Series Getting Started GuideOnSite Plug ‘n’ Play OnSite installation Chapter contentsChapter Connecting the twisted pair interface InstallationConnecting the Model 3088A to a “DCE” or “DTE” device Connecting the Model 3088A serial interfaceConnecting the Model 3088A/K serial interface Connecting the Model 3088A/K to an E1 NetworkConnect twisted pair 120 ohm to E1 network G.703/G.704 Powernetwork Connecting dual coaxial cable 75 ohm to E1 networkExternal AC universal power supply Connecting powerWARNING ton for assistance” on page DC PowerOperation Chapter contentsChapter Power Green Power-upLED status monitors DSL Green3088A/D with the X.21 interface Terminal GreenTM/ER Yellow LOS Red Model /KThe data path for the RDL is shown in figure PatternsChapter contents Chapter 5 Remote console operationEstablishing a Remote Console Session How to Connect5. Wait for the message Console Remote console connection established IntroductionWe can now enter commands on the remote console How to Disconnectsystem show status command shows that DSL link is not up Model 3088A Series Getting Started GuideFigure 18. Remote control session with LAL diagram Differences in Local and Remote Control Session BehaviorChapter contents Chapter 6 Software UpgradeIntroduction 2-3 minutes to complete. To upgrade the softwareChapter contents Chapter 7 Reset configuration to factory defaults1. Turn the Model 3088A off IntroductionChapter contents Chapter 8 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsContact information Patton support headquarters in the USAReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersChapter contents Appendix A Compliance informationCompliance SafetyRadio and TV Interference FCC Part CE Declaration of ConformityChapter contents Appendix B SpecificationsDiagnostics Serial connectorClocking modes DTE ratePower and power supply specifications ConfigurationTerminal Green 3088A/D with the X.21 interfaceLine coding Transmission lineExternal AC universal power supply External 48 VDC power supplyLine interface Line rates DSL lineG.SHDSL physical connection EnvironmentAppendix C Factory default values Chapter contentsFactory default values for software-configurable parameters Default value Factory default values for software-configurable parametersDefault value ParameterParameter Default valueAppendix D Factory replacement parts and accessories Chapter contentsFactory replacement parts and accessories Factory replacement parts and accessories Power SuppliesPower Adapters Chapter contents Appendix E Interface pinoutsLine port RS-232 interfaceRS-232 interface Line portSignal Signal DesignationE1 interface V.35 interfaceSignal SignalEthernet Console port X.21 interfaceD-sub-15 female connector DTE/DCE orientation Signal