Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual Introduction, minutes to complete. To upgrade the software

Models: 3088A

1 71

Page 50

2-3 minutes to complete. To upgrade the software:

Model 3088A Series Getting Started Guide	6 • Software Upgrade

Introduction

The software upgrade feature is available through BOOTP/TFTP. The software upgrade takes approximately

2-3 minutes to complete. To upgrade the software:

1.Connect to the Model 3088A via the Ethernet management port and a Telnet session.

2.Enter the system show info command to view the unit’s MAC address.

3.Configure a BOOTP/TFTP server to prepare for the upgrade.

4.Enter the system upgrade / yes command to begin the upgrade.

After approximately 2-3 minutes, the 3088A will operate with the upgraded software.

Introduction

Page 50

Image 50

Patton electronic 3088A manual Introduction, minutes to complete. To upgrade the software

Contents

Getting Started Guide OnSite Model 3088A SeriesG.SHDSL.bis CPE with fixed serial interface REGULATORY MODEL NUMBER 03340D4-0017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Table of ContentsSummary Table of Contents Configuration7 Reset configuration to factory defaults OnSite installationSoftware Upgrade OperationCompliance information SpecificationsFactory default values D Factory replacement parts and accessories Table of ContentsFactory default values for software-configurable parameters Factory replacement parts and accessoriesList of Figures List of Tables Structure About this guideAudience Note A note presents additional information or interesting sidelights Precautionsimpaired functioning Strictly follow the warning instructions to avoid personal injurySafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations ConventionChapter contents Chapter 1 General informationSerial interface types FeaturesOnSite 3088A overview Power input connector External AC universal power supplyExternal 48 VDC power supply Chapter contents ConfigurationChapter Introduction Software CLI configurationHardware DIP-switch configuration Description Table 2 lists the Model 3088A’s configurable parametersParameter Possible ValuesDescription Configuring the DIP switchesParameter Possible ValuesModel 3088A System reset modeDIP switch settings Function DIP switch settingsPosition FunctionS4-3 S4-2 through S4-8 Data RateS4-2 S4-4S4-4 S4-2S4-3 S4-5DCE/DTE operation Note This section applies to the following 3088A modelsEthernet Management Port DSL Link State In Progress, Success, Deactivated, or Idle E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoAlarms RED, YELLOW, BLUE. Active or Inactive DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing Syncsystem set password password Sets the system password Help CommandsSystem Configuration Commands System Status CommandsDSL Status Command DSL Configuration Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Clear Errcntrs CommandExample Command Line Interface Session Remote Consolesystem show config 2 Configurationsystem save config Model 3088A Series Getting Started GuideOnSite Plug ‘n’ Play Chapter OnSite installationChapter contents Installation Connecting the twisted pair interfaceConnecting the Model 3088A serial interface Connecting the Model 3088A to a “DCE” or “DTE” deviceConnect twisted pair 120 ohm to E1 network Connecting the Model 3088A/K serial interfaceConnecting the Model 3088A/K to an E1 Network Connecting dual coaxial cable 75 ohm to E1 network G.703/G.704 PowernetworkConnecting power External AC universal power supplyDC Power WARNING ton for assistance” on pageChapter OperationChapter contents LED status monitors Power-upPower Green DSL GreenTM/ER Yellow Terminal Green3088A/D with the X.21 interface LOS Red Model /KPatterns The data path for the RDL is shown in figureChapter 5 Remote console operation Chapter contents5. Wait for the message Console Remote console connection established How to ConnectEstablishing a Remote Console Session Introductionsystem show status command shows that DSL link is not up How to DisconnectWe can now enter commands on the remote console Model 3088A Series Getting Started GuideDifferences in Local and Remote Control Session Behavior Figure 18. Remote control session with LAL diagramChapter 6 Software Upgrade Chapter contents2-3 minutes to complete. To upgrade the software IntroductionChapter 7 Reset configuration to factory defaults Chapter contentsIntroduction 1. Turn the Model 3088A offChapter 8 Contacting Patton for assistance Chapter contentsContact information Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Patton support headquarters in the USAReturn for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix A Compliance information Chapter contentsRadio and TV Interference FCC Part SafetyCompliance CE Declaration of ConformityAppendix B Specifications Chapter contentsClocking modes Serial connectorDiagnostics DTE rateTerminal Green ConfigurationPower and power supply specifications 3088A/D with the X.21 interfaceExternal AC universal power supply Transmission lineLine coding External 48 VDC power supplyG.SHDSL physical connection Line rates DSL lineLine interface EnvironmentFactory default values for software-configurable parameters Appendix C Factory default valuesChapter contents Default value Factory default values for software-configurable parametersDefault value ParameterDefault value ParameterFactory replacement parts and accessories Appendix D Factory replacement parts and accessoriesChapter contents Power Adapters Factory replacement parts and accessoriesPower Supplies Line port Appendix E Interface pinoutsChapter contents RS-232 interfaceSignal Line portRS-232 interface Signal DesignationSignal V.35 interfaceE1 interface SignalD-sub-15 female connector DTE/DCE orientation X.21 interfaceEthernet Console port Signal