Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual Introduction, Software CLI configuration

Models: 3088A

1 71

Download 71 pages 59.37 Kb

Page 19

Introduction

Model 3088A Series Getting Started Guide	2 • Configuration

Introduction

You can configure the OnSite (see figure 3) in one of two ways:

•Software configuration using command line interface (CLI) via the console port

•Hardware configuration via DIP switches

Figure 3. OnSite (Model 3088A/D shown)

Software (CLI) configuration

To use the software configuration, you must set the S4 (Rate) DIP switches to the OFF position before power- ing up the OnSite. When it is set for software-configuration mode, the OnSite will read any configuration data previously saved to FLASH memory during system power-up. If no configuration data was previously saved to FLASH, then the OnSite will load the factory-default configuration from FLASH memory. After power-up, you may use console commands or the Embedded Operations Channel (EOC) to modify the configuration parameters.

Hardware (DIP-switch) configuration

To use DIP-switch configuration you must first set the DIP switches to a position other than all OFF or all ON before powering-up the OnSite. When all the DIP switches are set to any position other than all OFF or all ON the OnSite will operate in hardware (DIP-switch)-configuration mode. In DIP-switch-configuration mode the OnSite will read the DIP-switch settings during system startup and configure itself according to the switch set- tings.

Once you power-up the OnSite in DIP-switch mode, it will operate in DIP-switch mode until powered down. When operating in DIP-switch mode you cannot change any configuration settings:

•Changing the DIP switch settings while the device is running requires the dsl start command.

•If you attempt to modify the configuration by issuing console commands, the device will not execute your commands- except for the dsl start command and the show commands. Instead, the OnSite will respond with a message indicating the device is operating in DIP-switch-configuration mode.

•If you attempt to modify any configuration parameters via the EOC (by changing (EOC variables), the OnSite will not execute your changes.

Introduction

19

Image 19

Patton electronic 3088A manual Introduction, Software CLI configuration, Hardware DIP-switch configuration

Contents

REGULATORY MODEL NUMBER 03340D4-001 OnSite Model 3088A SeriesG.SHDSL.bis CPE with fixed serial interface Getting Started Guide7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Configuration Table of ContentsSummary Table of Contents Table of ContentsOperation OnSite installationSoftware Upgrade 7 Reset configuration to factory defaultsFactory default values SpecificationsCompliance information Factory replacement parts and accessories Table of ContentsFactory default values for software-configurable parameters D Factory replacement parts and accessoriesList of Figures List of Tables Audience About this guideStructure Strictly follow the warning instructions to avoid personal injury Precautionsimpaired functioning Note A note presents additional information or interesting sidelightsSafety when working with electricity Convention Typographical conventions used in this documentGeneral observations General conventionsChapter 1 General information Chapter contentsOnSite 3088A overview FeaturesSerial interface types External AC universal power supply Power input connectorExternal 48 VDC power supply Chapter ConfigurationChapter contents Hardware DIP-switch configuration Software CLI configurationIntroduction Possible Values Table 2 lists the Model 3088A’s configurable parametersParameter DescriptionPossible Values Configuring the DIP switchesParameter DescriptionDIP switch settings System reset modeModel 3088A Function DIP switch settingsPosition FunctionS4-4 S4-2 through S4-8 Data RateS4-2 S4-3S4-5 S4-2S4-3 S4-4Note This section applies to the following 3088A models DCE/DTE operationEthernet Management Port DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing Sync E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoAlarms RED, YELLOW, BLUE. Active or Inactive DSL Link State In Progress, Success, Deactivated, or IdleSystem Status Commands Help CommandsSystem Configuration Commands system set password password Sets the system passwordDSL Clear Errcntrs Command DSL Configuration Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Status CommandRemote Console Example Command Line Interface SessionModel 3088A Series Getting Started Guide 2 Configurationsystem save config system show configOnSite Plug ‘n’ Play Chapter contents OnSite installationChapter Connecting the twisted pair interface InstallationConnecting the Model 3088A to a “DCE” or “DTE” device Connecting the Model 3088A serial interfaceConnecting the Model 3088A/K to an E1 Network Connecting the Model 3088A/K serial interfaceConnect twisted pair 120 ohm to E1 network G.703/G.704 Powernetwork Connecting dual coaxial cable 75 ohm to E1 networkExternal AC universal power supply Connecting powerWARNING ton for assistance” on page DC PowerChapter contents OperationChapter DSL Green Power-upPower Green LED status monitorsLOS Red Model /K Terminal Green3088A/D with the X.21 interface TM/ER YellowThe data path for the RDL is shown in figure PatternsChapter contents Chapter 5 Remote console operationIntroduction How to ConnectEstablishing a Remote Console Session 5. Wait for the message Console Remote console connection establishedModel 3088A Series Getting Started Guide How to DisconnectWe can now enter commands on the remote console system show status command shows that DSL link is not upFigure 18. Remote control session with LAL diagram Differences in Local and Remote Control Session BehaviorChapter contents Chapter 6 Software UpgradeIntroduction 2-3 minutes to complete. To upgrade the softwareChapter contents Chapter 7 Reset configuration to factory defaults1. Turn the Model 3088A off IntroductionChapter contents Chapter 8 Contacting Patton for assistancePatton support headquarters in the USA Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyChapter contents Appendix A Compliance informationCE Declaration of Conformity SafetyCompliance Radio and TV Interference FCC PartChapter contents Appendix B SpecificationsDTE rate Serial connectorDiagnostics Clocking modes3088A/D with the X.21 interface ConfigurationPower and power supply specifications Terminal GreenExternal 48 VDC power supply Transmission lineLine coding External AC universal power supplyEnvironment Line rates DSL lineLine interface G.SHDSL physical connectionChapter contents Appendix C Factory default valuesFactory default values for software-configurable parameters Parameter Factory default values for software-configurable parametersDefault value Default valueParameter Default valueChapter contents Appendix D Factory replacement parts and accessoriesFactory replacement parts and accessories Power Supplies Factory replacement parts and accessoriesPower Adapters RS-232 interface Appendix E Interface pinoutsChapter contents Line portSignal Designation Line portRS-232 interface SignalSignal V.35 interfaceE1 interface SignalSignal X.21 interfaceEthernet Console port D-sub-15 female connector DTE/DCE orientation