Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual Summary Table of Contents, List of Figures, List of Tables

Models: 3088A

1 71

Download 71 pages 59.37 Kb

Page 4

Table of Contents

Table of Contents
	Summary Table of Contents	3
	Table of Contents	4
	List of Figures	8
	List of Tables	9
	About this guide	10
	Audience	10
	Structure	10
	Precautions	11
	Safety when working with electricity	12
	.......................................................................................................................................................................	13
	General observations	13
	Typographical conventions used in this document	13
	General conventions	13
1	General information	14
	OnSite 3088A overview	15
	Serial interface types	15
	Features	15
	Power input connector	16
	External AC universal power supply	16
	External 48 VDC power supply	17
2	Configuration	18
	Introduction	19
	Software (CLI) configuration	19
	Hardware (DIP-switch) configuration	19
	Configuring the DIP switches	21
	System reset mode	22
	DIP switch settings	22
	DIP switch settings	23
	S4-2 through S4-8: Data Rate	24
	DCE/DTE operation	26
	Ethernet Management Port	27
	Help Commands	29
	System Configuration Commands	29
	System Status Commands	29
	DSL Configuration Commands	30
	DSL Status Command	30
	DSL Clear Errcntrs Command	30
	E1 Configuration Commands	30
	E1 Status Commands	30
	Remote Console	31

4

Image 4

Patton electronic 3088A Summary Table of Contents, List of Figures, List of Tables, About this guide, Configuration

Contents

OnSite Model 3088A Series G.SHDSL.bis CPE with fixed serial interfaceGetting Started Guide REGULATORY MODEL NUMBER 03340D4-0017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Summary Table of ContentsTable of Contents ConfigurationOnSite installation Software Upgrade7 Reset configuration to factory defaults OperationFactory default values SpecificationsCompliance information Table of Contents Factory default values for software-configurable parametersD Factory replacement parts and accessories Factory replacement parts and accessoriesList of Figures List of Tables Audience About this guideStructure Precautions impaired functioningNote A note presents additional information or interesting sidelights Strictly follow the warning instructions to avoid personal injurySafety when working with electricity Typographical conventions used in this document General observationsGeneral conventions ConventionChapter contents Chapter 1 General informationOnSite 3088A overview FeaturesSerial interface types Power input connector External AC universal power supplyExternal 48 VDC power supply Chapter ConfigurationChapter contents Hardware DIP-switch configuration Software CLI configurationIntroduction Table 2 lists the Model 3088A’s configurable parameters ParameterDescription Possible ValuesConfiguring the DIP switches ParameterDescription Possible ValuesDIP switch settings System reset modeModel 3088A DIP switch settings PositionFunction FunctionS4-2 through S4-8 Data Rate S4-2S4-3 S4-4S4-2 S4-3S4-4 S4-5DCE/DTE operation Note This section applies to the following 3088A modelsEthernet Management Port E1 Frame Errors Yes or No E1 Buffer Slips Yes or No Alarms RED, YELLOW, BLUE. Active or InactiveDSL Link State In Progress, Success, Deactivated, or Idle DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing SyncHelp Commands System Configuration Commandssystem set password password Sets the system password System Status CommandsDSL Configuration Commands dsl set lineprobe enableddisabled Enable or disable line probeDSL Status Command DSL Clear Errcntrs CommandExample Command Line Interface Session Remote Console2 Configuration system save configsystem show config Model 3088A Series Getting Started GuideOnSite Plug ‘n’ Play Chapter contents OnSite installationChapter Installation Connecting the twisted pair interfaceConnecting the Model 3088A serial interface Connecting the Model 3088A to a “DCE” or “DTE” deviceConnecting the Model 3088A/K to an E1 Network Connecting the Model 3088A/K serial interfaceConnect twisted pair 120 ohm to E1 network Connecting dual coaxial cable 75 ohm to E1 network G.703/G.704 PowernetworkConnecting power External AC universal power supplyDC Power WARNING ton for assistance” on pageChapter contents OperationChapter Power-up Power GreenLED status monitors DSL GreenTerminal Green 3088A/D with the X.21 interfaceTM/ER Yellow LOS Red Model /KPatterns The data path for the RDL is shown in figureChapter 5 Remote console operation Chapter contentsHow to Connect Establishing a Remote Console Session5. Wait for the message Console Remote console connection established IntroductionHow to Disconnect We can now enter commands on the remote consolesystem show status command shows that DSL link is not up Model 3088A Series Getting Started GuideDifferences in Local and Remote Control Session Behavior Figure 18. Remote control session with LAL diagramChapter 6 Software Upgrade Chapter contents2-3 minutes to complete. To upgrade the software IntroductionChapter 7 Reset configuration to factory defaults Chapter contentsIntroduction 1. Turn the Model 3088A offChapter 8 Contacting Patton for assistance Chapter contentsWarranty Service and Returned Merchandise Authorizations RMAs Warranty coverageContact information Patton support headquarters in the USAOut-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix A Compliance information Chapter contentsSafety ComplianceRadio and TV Interference FCC Part CE Declaration of ConformityAppendix B Specifications Chapter contentsSerial connector DiagnosticsClocking modes DTE rateConfiguration Power and power supply specificationsTerminal Green 3088A/D with the X.21 interfaceTransmission line Line codingExternal AC universal power supply External 48 VDC power supplyLine rates DSL line Line interfaceG.SHDSL physical connection EnvironmentChapter contents Appendix C Factory default valuesFactory default values for software-configurable parameters Factory default values for software-configurable parameters Default valueDefault value ParameterDefault value ParameterChapter contents Appendix D Factory replacement parts and accessoriesFactory replacement parts and accessories Power Supplies Factory replacement parts and accessoriesPower Adapters Appendix E Interface pinouts Chapter contentsLine port RS-232 interfaceLine port RS-232 interfaceSignal Signal DesignationV.35 interface E1 interfaceSignal SignalX.21 interface Ethernet Console portD-sub-15 female connector DTE/DCE orientation Signal