Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual S4-2, S4-3, S4-4, S4-5, S4-6, S4-7, S4-8, Data Rate kbps

Models: 3088A

1 71

Download 71 pages 59.37 Kb

Page 25

Model 3088A Series Getting Started Guide	2 • Configuration

Table 5. S4-2 through S4-8 Data Rate DIP switch settings (Continued)

S4-2	S4-3	S4-4	S4-5	S4-6	S4-7	S4-8	Data Rate (kbps)

OFF	ON	OFF	OFF	OFF	OFF	ON	2240
OFF	ON	OFF	OFF	OFF	ON	OFF	2304

OFF	ON	OFF	OFF	OFF	ON	ON	2368
OFF	ON	OFF	OFF	ON	OFF	OFF	2432

OFF	ON	OFF	OFF	ON	OFF	ON	2496
OFF	ON	OFF	OFF	ON	ON	OFF	2560

OFF	ON	OFF	OFF	ON	ON	ON	2624
OFF	ON	OFF	ON	OFF	OFF	OFF	2688

OFF	ON	OFF	ON	OFF	OFF	ON	2752
OFF	ON	OFF	ON	OFF	ON	OFF	2816

OFF	ON	OFF	ON	OFF	ON	ON	2880
OFF	ON	OFF	ON	ON	OFF	OFF	2944

OFF	ON	OFF	ON	ON	OFF	ON	3008
OFF	ON	OFF	ON	ON	ON	OFF	3072

OFF	ON	OFF	ON	ON	ON	ON	3136
OFF	ON	ON	OFF	OFF	OFF	OFF	3200

OFF	ON	ON	OFF	OFF	OFF	ON	3264
OFF	ON	ON	OFF	OFF	ON	OFF	3328

OFF	ON	ON	OFF	OFF	ON	ON	3392
OFF	ON	ON	OFF	ON	OFF	OFF	3456

OFF	ON	ON	OFF	ON	OFF	ON	3520
OFF	ON	ON	OFF	ON	ON	OFF	3584

OFF	ON	ON	OFF	ON	ON	ON	3648
OFF	ON	ON	ON	OFF	OFF	OFF	3712

OFF	ON	ON	ON	OFF	OFF	ON	3776
OFF	ON	ON	ON	OFF	ON	OFF	3840

OFF	ON	ON	ON	OFF	ON	ON	3904
OFF	ON	ON	ON	ON	OFF	OFF	3968

OFF	ON	ON	ON	ON	OFF	ON	4032
OFF	ON	ON	ON	ON	ON	OFF	4096

OFF	ON	ON	ON	ON	ON	ON	4160
ON	OFF	OFF	OFF	OFF	OFF	OFF	4224

ON	OFF	OFF	OFF	OFF	OFF	ON	4288
ON	OFF	OFF	OFF	OFF	ON	OFF	4352

ON	OFF	OFF	OFF	OFF	ON	ON	4416
ON	OFF	OFF	OFF	ON	OFF	OFF	4480

ON	OFF	OFF	OFF	ON	OFF	ON	4544
ON	OFF	OFF	OFF	ON	ON	OFF	4608

Introduction

25

Image 25

Patton electronic 3088A manual S4-2, S4-3, S4-4, S4-5, S4-6, S4-7, S4-8, Data Rate kbps

Contents

G.SHDSL.bis CPE with fixed serial interface OnSite Model 3088A SeriesGetting Started Guide REGULATORY MODEL NUMBER 03340D4-0017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Summary Table of Contents Table of ContentsTable of Contents ConfigurationSoftware Upgrade OnSite installation7 Reset configuration to factory defaults OperationFactory default values SpecificationsCompliance information Factory default values for software-configurable parameters Table of ContentsD Factory replacement parts and accessories Factory replacement parts and accessoriesList of Figures List of Tables Audience About this guideStructure impaired functioning PrecautionsNote A note presents additional information or interesting sidelights Strictly follow the warning instructions to avoid personal injurySafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions ConventionChapter 1 General information Chapter contentsOnSite 3088A overview FeaturesSerial interface types External AC universal power supply Power input connectorExternal 48 VDC power supply Chapter ConfigurationChapter contents Hardware DIP-switch configuration Software CLI configurationIntroduction Parameter Table 2 lists the Model 3088A’s configurable parametersDescription Possible ValuesParameter Configuring the DIP switchesDescription Possible ValuesDIP switch settings System reset modeModel 3088A Position DIP switch settingsFunction FunctionS4-2 S4-2 through S4-8 Data RateS4-3 S4-4S4-3 S4-2S4-4 S4-5Note This section applies to the following 3088A models DCE/DTE operationEthernet Management Port Alarms RED, YELLOW, BLUE. Active or Inactive E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoDSL Link State In Progress, Success, Deactivated, or Idle DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing SyncSystem Configuration Commands Help Commandssystem set password password Sets the system password System Status Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Configuration CommandsDSL Status Command DSL Clear Errcntrs CommandRemote Console Example Command Line Interface Sessionsystem save config 2 Configurationsystem show config Model 3088A Series Getting Started GuideOnSite Plug ‘n’ Play Chapter contents OnSite installationChapter Connecting the twisted pair interface InstallationConnecting the Model 3088A to a “DCE” or “DTE” device Connecting the Model 3088A serial interfaceConnecting the Model 3088A/K to an E1 Network Connecting the Model 3088A/K serial interfaceConnect twisted pair 120 ohm to E1 network G.703/G.704 Powernetwork Connecting dual coaxial cable 75 ohm to E1 networkExternal AC universal power supply Connecting powerWARNING ton for assistance” on page DC PowerChapter contents OperationChapter Power Green Power-upLED status monitors DSL Green3088A/D with the X.21 interface Terminal GreenTM/ER Yellow LOS Red Model /KThe data path for the RDL is shown in figure PatternsChapter contents Chapter 5 Remote console operationEstablishing a Remote Console Session How to Connect5. Wait for the message Console Remote console connection established IntroductionWe can now enter commands on the remote console How to Disconnectsystem show status command shows that DSL link is not up Model 3088A Series Getting Started GuideFigure 18. Remote control session with LAL diagram Differences in Local and Remote Control Session BehaviorChapter contents Chapter 6 Software UpgradeIntroduction 2-3 minutes to complete. To upgrade the softwareChapter contents Chapter 7 Reset configuration to factory defaults1. Turn the Model 3088A off IntroductionChapter contents Chapter 8 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsContact information Patton support headquarters in the USAReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersChapter contents Appendix A Compliance informationCompliance SafetyRadio and TV Interference FCC Part CE Declaration of ConformityChapter contents Appendix B SpecificationsDiagnostics Serial connectorClocking modes DTE ratePower and power supply specifications ConfigurationTerminal Green 3088A/D with the X.21 interfaceLine coding Transmission lineExternal AC universal power supply External 48 VDC power supplyLine interface Line rates DSL lineG.SHDSL physical connection EnvironmentChapter contents Appendix C Factory default valuesFactory default values for software-configurable parameters Default value Factory default values for software-configurable parametersDefault value ParameterParameter Default valueChapter contents Appendix D Factory replacement parts and accessoriesFactory replacement parts and accessories Power Supplies Factory replacement parts and accessoriesPower Adapters Chapter contents Appendix E Interface pinoutsLine port RS-232 interfaceRS-232 interface Line portSignal Signal DesignationE1 interface V.35 interfaceSignal SignalEthernet Console port X.21 interfaceD-sub-15 female connector DTE/DCE orientation Signal