Manuals / Patton electronic / Computer Equipment / Network Cables

Patton electronic 3088A manual Summary Table of Contents

Models: 3088A

1 71

Page 3

Summary Table of Contents
1	General information	14
2	Configuration	18
3	OnSite installation	34
4	Operation	41
5	Remote console operation	45
6	Software Upgrade	49
7	Reset configuration to factory defaults	51
8	Contacting Patton for assistance	53
A	Compliance information	56
B	Specifications	58
C	Factory default values	63
D	Factory replacement parts and accessories	66
E	Interface pinouts	68

Page 3

Image 3

Contents

REGULATORY MODEL NUMBER 03340D4-001 OnSite Model 3088A SeriesG.SHDSL.bis CPE with fixed serial interface Getting Started Guide7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Configuration Table of ContentsSummary Table of Contents Table of ContentsOperation OnSite installationSoftware Upgrade 7 Reset configuration to factory defaultsSpecifications Factory default valuesCompliance information Factory replacement parts and accessories Table of ContentsFactory default values for software-configurable parameters D Factory replacement parts and accessoriesList of Figures List of Tables About this guide AudienceStructure Strictly follow the warning instructions to avoid personal injury Precautionsimpaired functioning Note A note presents additional information or interesting sidelightsSafety when working with electricity Convention Typographical conventions used in this documentGeneral observations General conventionsChapter 1 General information Chapter contentsFeatures OnSite 3088A overviewSerial interface types External AC universal power supply Power input connectorExternal 48 VDC power supply Configuration ChapterChapter contents Software CLI configuration Hardware DIP-switch configurationIntroduction Possible Values Table 2 lists the Model 3088A’s configurable parametersParameter DescriptionPossible Values Configuring the DIP switchesParameter DescriptionSystem reset mode DIP switch settingsModel 3088A Function DIP switch settingsPosition FunctionS4-4 S4-2 through S4-8 Data RateS4-2 S4-3S4-5 S4-2S4-3 S4-4Note This section applies to the following 3088A models DCE/DTE operationEthernet Management Port DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing Sync E1 Frame Errors Yes or No E1 Buffer Slips Yes or NoAlarms RED, YELLOW, BLUE. Active or Inactive DSL Link State In Progress, Success, Deactivated, or IdleSystem Status Commands Help CommandsSystem Configuration Commands system set password password Sets the system passwordDSL Clear Errcntrs Command DSL Configuration Commandsdsl set lineprobe enableddisabled Enable or disable line probe DSL Status CommandRemote Console Example Command Line Interface SessionModel 3088A Series Getting Started Guide 2 Configurationsystem save config system show configOnSite Plug ‘n’ Play OnSite installation Chapter contentsChapter Connecting the twisted pair interface InstallationConnecting the Model 3088A to a “DCE” or “DTE” device Connecting the Model 3088A serial interfaceConnecting the Model 3088A/K serial interface Connecting the Model 3088A/K to an E1 NetworkConnect twisted pair 120 ohm to E1 network G.703/G.704 Powernetwork Connecting dual coaxial cable 75 ohm to E1 networkExternal AC universal power supply Connecting powerWARNING ton for assistance” on page DC PowerOperation Chapter contentsChapter DSL Green Power-upPower Green LED status monitorsLOS Red Model /K Terminal Green3088A/D with the X.21 interface TM/ER YellowThe data path for the RDL is shown in figure PatternsChapter contents Chapter 5 Remote console operationIntroduction How to ConnectEstablishing a Remote Console Session 5. Wait for the message Console Remote console connection establishedModel 3088A Series Getting Started Guide How to DisconnectWe can now enter commands on the remote console system show status command shows that DSL link is not upFigure 18. Remote control session with LAL diagram Differences in Local and Remote Control Session BehaviorChapter contents Chapter 6 Software UpgradeIntroduction 2-3 minutes to complete. To upgrade the softwareChapter contents Chapter 7 Reset configuration to factory defaults1. Turn the Model 3088A off IntroductionChapter contents Chapter 8 Contacting Patton for assistancePatton support headquarters in the USA Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyChapter contents Appendix A Compliance informationCE Declaration of Conformity SafetyCompliance Radio and TV Interference FCC PartChapter contents Appendix B SpecificationsDTE rate Serial connectorDiagnostics Clocking modes3088A/D with the X.21 interface ConfigurationPower and power supply specifications Terminal GreenExternal 48 VDC power supply Transmission lineLine coding External AC universal power supplyEnvironment Line rates DSL lineLine interface G.SHDSL physical connectionAppendix C Factory default values Chapter contentsFactory default values for software-configurable parameters Parameter Factory default values for software-configurable parametersDefault value Default valueParameter Default valueAppendix D Factory replacement parts and accessories Chapter contentsFactory replacement parts and accessories Factory replacement parts and accessories Power SuppliesPower Adapters RS-232 interface Appendix E Interface pinoutsChapter contents Line portSignal Designation Line portRS-232 interface SignalSignal V.35 interfaceE1 interface SignalSignal X.21 interfaceEthernet Console port D-sub-15 female connector DTE/DCE orientation