Multiquip tp24 manual Electric motor components/set-up, Electric Motor Components, Saw Set-Up

Page 16

electric motor components/set-up

Electric Motor Components

Figure 3 shows the location of the components of the electric motor.

115 VAC, 60 Hz

SINGLE -PHASE

ELECTRIC MOTOR

OVERCURRENT

BREAKER BUTTON

ELECTRIC WATER	ELECTRIC
PUMP AC	MOTOR
RECEPTACLE	ON/OFF SWITCH

Figure 3. Electric Motor Components

Saw Set-Up

WARNING

Whenever cleaning, adjusting or lubricating any part of the saw, make certain to place the power ON/OFF switch in the OFF position and disconnect the plug from the power source.

1.Open the shipping container carefully, lift the saw by its carrying handles and place it on a suitable table or platform. Make sure the table or platform can support the weight of the saw.

2.Make sure that the following items are found in the container:

Saw	Water Pump
Water Tray	Rear Drip Tray
Drain Plug	Owner’s Manual
Universal Wrench	Rip Guide
Saw Blade

3.Slide water pump onto U-shaped bracket located at the bottom of the frame. See Figure 6.

4.Slide cutting head onto the post. Secure cutting head to the shaft using provided flat washer, lock washer and nut. Attach cutting depth control knob and washer to the cutting head through the slot located underneath the belt guard. See Figure 4.

5.Mount blade guard onto shaft protruding from the side of the cutting head. Secure the blade guard in place using the provided serrated washer and blade guard knob.

6.Attach rear drip tray to the water tray.

BLADE

GUARD

KNOB

REAR		BLADE
DRIP	CUTTING	GUARD
TRAY	HEAD

CUTTING
DEPTH
CONTROL
KNOB	WATER
	WATER
	TRAY

SHAFT

Figure 4. Saw Assembly

7.If using the optional support stand, assemble as described in the Support Stand Assembly section. Make sure that the saw is secured on the support stand as instructed.

support Stand Assembly (Optional)

Refer to Figure 5 for location of components.

1.Remove the folding stand from its box.

2.While holding the stand upright, spread both sets of legs apart and swing the workbench over and on top of the legs.

3.Seat the saw securely onto the stand.

page 16 — TP24 TILE SAW • operation and parts manual — rev. #2 (04/12/12)

Image 16

Contents Model TP24 Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents TP24 Tile SawChoose from three easy options Safety Information SaFeTy meSSageSGeneraL SaFeTy SaW SaFeTy BLade SaFeTyELeCTrIC moTor SaFeTy Power Cord/Cable SafetyLIFTIng SaFeTy TranSporTIng SaFeTySpecifications 3200Dimensions DimensionsAccessories/Replacement Parts FeaturesGeneral information Dry Cutting ApplicationsTP24 Tile SAW operation and parts manual rev. #2 04/12/12 Saw components Saw ComponentsStopper Place stopper in water tray when filling with water Support Stand Assembly Optional Electric motor components/set-upElectric Motor Components Saw Set-UpConnecting the water Pump Install drain plug in water traySet-up Refer to FigureBlade Components BladesCutting Depth Blade Installation Connecting the Power Sawing Guides Using the Cutting TablePlace the power ON/OFF switch in the OFF position down Never grab or touch a live Power cord with wet hands,Using the Rip Guide Sawing guidesPerforming Diagonal Cuts Performing Miter CutsOperation Start-up ProcedureStarting or attempting to operate the saw Shut down Procedure Wait for the cutting blade to stop rotatingBasic Maintenance Inspect the cutting table periodically. Replace worn partsMaintenance intervals After wet cleaning and before using the machine againBefore not using the machine for a prolonged period of time After not using the machine for a prolonged period of timeWater pump maintenance Belt replacementBearing housing removal Take off the old belt and replace with new beltBearing Housing Installation Bearing Housing RemovalRealignment Method Intially, but shifts apart as the table travels alongRail, proceed to Method Forth. If the table binds against the rail at anyFurther adjustment-repeat step MethodTable from the guide rails. See Figure Shim may be requiredLeveling Adjustment Transporting the sawWiring diagram electric motor Electric Motor Wiring DiagramTroubleshooting blade Blade TroubleshootingTroubleshooting Saw Saw TroubleshootingExplanation of Code in Remarks Column Switch, toggle 15A Suggested Spare PartsTP24 tile saw with electric motor 1 to 3 units BeltMain SAW Assy Part Name Cutting Head Assy Cutting Head Assy Electric motor Assy QTY Remarks Cutting table assy Part Name QTY Blade guard assy Part Name Bearing housing assy Bearing housing assy Switch box assy Remarks Tools and accessories TP100102 TPSDT1010stTerms and Conditions of Sale Parts FreIgHT poLICyTP24 Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help