Multiquip tp24 manual Silicosis/Respiratory Warnings, Silicosis Warning

Page 3

Silicosis/Respiratory Warnings

WARNING

SILICOSIS WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, California and some other authorities have listed respirable crystalline silica as a substance known to cause cancer. When cutting such materials, always follow the respiratory precautions mentioned above.

WARNING

RESPIRATORY HAZARDS

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good work practices and follow the recommendations of the manufacturers or suppliers, OSHA/NIOSH, and occupational and trade associations. Water should be used for dust suppression when wet cutting is feasible. When the hazards from inhalation of dust, mists and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the materials being used.

TP24 TILE SAW • operation and parts manual — rev. #2 (04/12/12) — page 3

Image 3
Contents Model TP24 Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsTP24 Tile Saw Table of ContentsChoose from three easy options SaFeTy meSSageS Safety InformationGeneraL SaFeTy BLade SaFeTy SaW SaFeTyTranSporTIng SaFeTy ELeCTrIC moTor SaFeTyPower Cord/Cable Safety LIFTIng SaFeTy3200 SpecificationsDimensions DimensionsDry Cutting Applications Accessories/Replacement PartsFeatures General informationTP24 Tile SAW operation and parts manual rev. #2 04/12/12 Saw Components Saw componentsStopper Place stopper in water tray when filling with water Saw Set-Up Support Stand Assembly OptionalElectric motor components/set-up Electric Motor ComponentsRefer to Figure Connecting the water PumpInstall drain plug in water tray Set-upBlades Blade ComponentsCutting Depth Blade Installation Never grab or touch a live Power cord with wet hands, Connecting the PowerSawing Guides Using the Cutting Table Place the power ON/OFF switch in the OFF position downPerforming Miter Cuts Using the Rip GuideSawing guides Performing Diagonal CutsStart-up Procedure OperationStarting or attempting to operate the saw Wait for the cutting blade to stop rotating Shut down ProcedureInspect the cutting table periodically. Replace worn parts Basic MaintenanceAfter not using the machine for a prolonged period of time Maintenance intervalsAfter wet cleaning and before using the machine again Before not using the machine for a prolonged period of timeTake off the old belt and replace with new belt Water pump maintenanceBelt replacement Bearing housing removalBearing Housing Removal Bearing Housing InstallationForth. If the table binds against the rail at any Realignment MethodIntially, but shifts apart as the table travels along Rail, proceed to MethodShim may be required Further adjustment-repeat stepMethod Table from the guide rails. See FigureTransporting the saw Leveling AdjustmentElectric Motor Wiring Diagram Wiring diagram electric motorBlade Troubleshooting Troubleshooting bladeSaw Troubleshooting Troubleshooting SawExplanation of Code in Remarks Column Belt Switch, toggle 15ASuggested Spare Parts TP24 tile saw with electric motor 1 to 3 unitsMain SAW Assy Part Name Cutting Head Assy Cutting Head Assy Electric motor Assy QTY Remarks Cutting table assy Part Name QTY Blade guard assy Part Name Bearing housing assy Bearing housing assy Switch box assy Remarks Tools and accessories TPSDT1010st TP100102FreIgHT poLICy Terms and Conditions of Sale PartsTP24 Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help